Tryton TMM10533, Руководство по эксплуатации

Страница: 7 / 52

7
n
the position - .
The green LED indicator for the power voltage ( 6 ) goes on when the
Rotate the tool holder to set the chisel to
machine is connected to the electric power grid. When the indicator is on
the desired working position.
and the machine fails to start it may be the case that carbon brushes are
Set the operation mode selector switch
worn out or the electric circuit of the machine motor is damaged.
( 10 ) to the position 'Chiseling'. Thus, the
When the LED indicator for the power voltage ( 6 ) is off and the machine
tool holder is locked in its position.
fails to start it may be the case that the On/Off trigger or the power cord is
While chiseling the operation mode selector switch ( 10 ) must always
defective.
remain in the position 'Chiseling'.
The red LED indicator of brush wear ( 7 ) goes on when carbon brushes are
n
Setting of rotation direction
nearly about to be worn out, which shows that the machine needs
The rotation direction switch ( 9 ) can be used to reverse direction of the
maintenance. After about 8 hours of brush wear indication the machine
tool rotation.
motor shall be automatically switched off.
However, the switch cannot be repositioned when the On/Off trigger ( 8 )
is depressed.
NOTE: Do never attempt to reverse the rotation direction when the SDS-
plus tool holder ( 1 ) is in motion. Otherwise the machine can be damaged.
Clockwise rotation: Move rotation direction switch ( 9 ) home
to the appropriate position marked with the symbol
Anticlockwise rotation: Move rotation direction switch ( 9 )
home to the appropriate position marked with the symbol
n
n
Setting of the rotation speed/impact rate
By adjustment of the force the On/Off trigger ( 8 ) is depressed with one
can control the rotation speed/impact rate in the infinitely continuous
manner.
Slight depressing the On/Off trigger (
8 ) moves the machine with the low
rotation speed/impact rate
The stronger the On/Off trigger (
8 ) is depressed the faster the machine
rotates.
'No-impact drilling'
MANUFACTURER:
PROFIX Ltd.,
34 Marywilska Street,
03-228 Warsaw, POLAND.
n
Overload safety coupling
PROTECTION OF THE ENVIRONMENT:
When the running tool is seized or jammed, the driving torque is no
longer transmitted to the spindle of the hammer drill. Due to excessive
The symbol nearby denotes that old equipment must
forces and torques occurring when the machine is running operators
never be thrown away together with other waste (with the
should always reliably held the machine with two hands and take a
penalty of a fine). Hazardous components of electronic
steady position of the body.
equipment may adversely affect the natural environment and
human health.
When the running tool is seized, it is necessary to switch the machine off
and release the tool. Be careful as switching the seized machine on leads
Each household may contribute to the recovery and reuse (recycling) of
to strong and rapid reaction torques. old machinery and equipment. Both in Poland and Europe a system for
LED indicators
STORAGE AND MAINTENANCE:
Generally, this power tool does not require any special maintenance.
Store the machine in a place away from children, keep it clean and
protect from humidity and dust. Storage conditions should exclude any
mechanical damage and weathering.
External plastic parts of the machine can be cleaned with use of a wet
cloth and a mild cleaning agent.
NOTE: NEVER use any solvent-based cleaning agents.
Turning on/off
After drilling in concrete, in intensely dusty environments it is
To turn the power tool on press its switch ( 8 ) button and keep it pressed.
recommended to remove dust from ventilation openings and the drill
To turn the power tool on press its switch ( 8 ) button and keep it pressed.
chuck with a stream of compressed air. It will protect bearings and
To lock the switch in on position press the lock ( 5 ). remove the dust obstructing motor cooling air supply.
To turn the power tool off just release the switch ( 8 ) button or, when it
TRANSPORTATION:
is locked with switch lock ( 5 ), press it for a moment and then release it.
The hammer drill should be transported and stored in its transportation
case that protects the tool from moisture, penetration of dust and fine
particles. In particular it is necessary to protect the ventilation openings.
Small objects that get into the device can damage the motor.
TROUBLESHOOTING GUIDE (TYPICAL PROBLEMS):
The hammer drill fails to work:
- check whether the rotation direction switch is not set to the middle
position;
- check whether the power cord is properly connected and check fuses.
TIPS REGARDING OPERATION:
The hammer drill works with jerks or sparks are visible:
ź
After a longer operation at low speeds run the power tool at its
- check and replace carbon brushes.
maximum speed with no load for about 3 minutes to cool it down.
NOTE! Carbon brushes can be replaced only by competent electricians.
ź
To drill holes in ceramic tiles set the operation mode switch ( 10 ) to
- If the power tool does not work despite being supplied from a proper
position . Once the hole in the ceramic tile is ready, set
power source, have the tool repaired sending it to the service center . The
the operation mode switch to position «impact drill» and continue
addresses are provided in the warranty card.
drilling in this mode.
ź
When drilling in concrete, stone or walls hard alloy drill bits should be
used.
ź
When drilling in metal use sharp metal drill bits only.
NOTE:
4