Tryton TMM10533, Руководство по эксплуатации

Страница: 5 / 52

5
n
:
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
maintained properly, the vibration level may differ from the values
given. The above-mentioned causes may lead to higher exposure to
vibrations during the whole work time.
One must implement additional safety measures to protect the operators
from exposure to vibrations, such as maintenance of the electric tool and
n
work tools, assurance of proper hand temperature, or determination of
the sequence of work operations.
Delivery kit
ź
Hammer drill – 1 pc.
ź
Auxiliary handle – 1 pc.
ź
Drilling depth limiter – 1 pc.
ź
Additional drilling chuck (13 mm) with a toothed ring – 1 pc.
ź
Key for the drilling chuck with a toothed ring – 1 pc.
ź
SDS-plus locking pin with a bolt for the drilling chuck – 1 pc.
ź
Flat chisel – 1 pc.
ź
Point chisel – 1 pc.
ź
SDS-plus drilling tools – 3 pcs . ( 8, 10, 12 mm)
ź
Rubber ring for dust collection – 1 pc.
ź
Transportation case – 1 pc.
ź
User's manual - 1 p c.
ź
Warranty card - 1 p c.
BEFORE YOU START:
1. Make sure that parameters of the power supplying source correspond
to parameters required for the hammer drill specified on its rating
plate.
2. Make sure that the On/Off trigger ( 8 ) of the hammer drill is in the Off
position and the locking button ( 5 ) for the trigger is released. Do
never put the working hammer drill aside when the locking button is
engaged. The locking button is released by depressing the trigger (
8 )
for the second time.
3 . The auxiliary handle ( 12 ) is to be attached by encompassing the
drilling chuck with the handle clamp and then the clamp is locked by
rotating the handle clockwise.
The auxiliary handle can be swiveled to whichever direction to enable
the operator to work in a convenient position of the body and to avoid
excessive fatigue. After rotating the handle anticlockwise swivel it to
the desired position and the retighten the clamp by rotating the
handle clockwise for final fixation.
Depress the fixing button (
4 ) to slide the drilling depth limiter ( 13 )
into the opening in the auxiliary handle and then lock it by releasing
the fixing button. Notches on the drilling depth limiter should be seen
SPECIFICATIONS:
from the top.
4. While working with an electric extension cable make sure that
parameters of the extension cable and cross-sections of wires
correspond to electric parameters of the hammer drill. Extension
cords should be as short as possible. When in use extension cords
must be fully uncoiled.
ADJUSTMENT DURING WORKING WITH THE TOOL:
n
Adjustment of the drilling depth (Fig. B )
The drilling depth limiter ( 13 ) is designed to set the desired depth of the
drilling bit immersion X into the material. For that purpose do the
following:
ź
insert the shank of the SDS-plus working tool into the holder ( 1 ) and
drive it home. Otherwise, excessive play of the SDS-plus tool may lead
to incorrect setting of the drilling depth;
ź
depress the fixing button( 4 ) for the drilling depth limiter and slide the
limiter so much as to make the distance between the tip of the drilling
bit and the tip of the limiter correspond to the desired drilling depth
X ,
ź
lock the depth limiter by releasing the fixing button.
Device components
The numbering of device components refers to graphics presented on page
2 of the user's manual:
1. SDS-plus tool holder
2. Dust protection hood
3. Locking sleeve
4. Fixing button to fit the drilling depth limiter
5. On/Off trigger locking button
6. Power voltage LED indicator (green)
7 . Brush wear LED indicator (red)
8. On/Off trigger
9. Rotation direction switch
10. Operation mode selector switch
11. Button to release locking of the operation mode selector switch
12. Auxiliary handle
13. Drilling depth limiter
14. Securing bolt for the drilling chuck with a toothed ring
15. Drilling chuck with a toothed ring
16. Adapter stud to fix the drilling chuck to the SDS-plus socket
17. Key for the drilling chuck with a toothed ring
18. Drilling chuck sleeve
Frequency
50 Hz
Power consumption 1050 W
No load speed n
0
T ool holder
Maximum hole diameter
steel
concrete -
26 mm
wood - 4 0 mm
- 1 3 mm
Sound pressure level (LpA)
Sound power level (LwA)
0-1100 rpm
SDS-plus
91,8 dB(A)
102,8 dB(A)
Equipment Class
Ingress protection
Impact rate (bpm) /Impact energy
-1
0-5 2 0 0 min / 3,5 J
Weight (with no accessories) 3,4 kg
IP20
II
Voltage 230-240 V
Max. diameter of drilling bits fixed in the drilling chuck 26 mm
Vibration level according to valid standard :
- hammer drilling in
concrete a
h HD
- t olerance of measurements
EN 60745-1:2009
2
15,668 m/s
2
13,09 m/s
15,81 m/s
2
14,092 m/s
2
2
1,5 m/s
main handle
auxiliary
handle
- chiseling a
h Cheq
main handle
auxiliary
handle