8
«
»
Never dispose of batteries in water.
«Read this instruction before switching on the
power supply and starting the work.»
TROUBLESHOOTING GUIDE:
PROBLEM
POSSIBLE CAUSE
REMEDY
Irregularities of the motor
operation.
Worn carbon brushes of the motor. Have the brushes replaced at a service workshop.
The tool (drill/screwdriver)
fails to operate.
No power voltage, damaged
motor or the power trigger.
Check the battery status, recharge or replace with a new one when necessary.
When the problem persists hand over the tool for repair at a service workshop.
Please refer to the warranty sheet for addresses of authorized workshops.
Battery low.
Recharge the battery.
«
»
Never dispose of batteries in fire.
«
»
Protect the battery against heat, e. g., against
continuous intense sunlight.
«
»
For indoor use only
.
n
Driving screws
MANUFACTURER:
It is recommended to drill the pilot borehole first. The pilot borehole must
PROFIX Co.Ltd.,
be a little deeper and with a less diameter than the outer diameter of the
34
Marywilska Street,
screw thread. When the screw is to be driven within the vicinity of the
03-228 Warsaw,
POLAND.
material edge the pilot borehole prevents from undesired chipping of the
This appliance is in conformity with national and European standards as
material.
well as with general safety guidelines.
If the screw is driven with abnormal difficulty the screw must be retracted
NOTE:
In case of technical issues, contact an authorised technical service.
and the pilot borehole diameter should be enlarged.
Any repairs are allowed to be carried out exclusively by qualified staff with
Anyway, when problem to drive the screw in persists (e.g. in case of hard
use of original spare parts.
wood grades) try to use a lubricating agent (e.g. liquid soap). Press the
tool to the screw with sufficient force to avoid spontaneous rotation of the
PICTOGRAMS:
driving bit in the screw head. Use only those bits that accurately match
Explanation of the icons located on the nominal plate and the
the bit head. When the screw head is damaged further driving the screw
information tags
:
in or out may prove infeasible.
STORAGE AND MAINTENANCE:
The tool in principle does not require any special maintenance or service.
The tool must be stored in a place that is not accessible to children and
must be kept clean and protected from moisture and dust. The storage
conditions should prevent potential mechanical damage and impact of
the weather conditions.
CAUTION:
Remember to always disconnect the battery from the tool prior
to starting the cleaning operations and
unplug the charger from the outlet.
The charger may be cleaned exclusively with use of a dry cloth. Use also a
clean cloth to clean regularly the ventilation openings of the tool to keep
them patent. From time to time disassemble the grip and remove dust
and other rubbish from the interior.
The tool housing must be cleaned with use of a moistened cloth small
quantity of soap and then wiped dry. Do not use any detergents or
PROTECTION OF THE ENVIRONMENT:
solvents as they can damage parts made from plastics. After cleaning let
NOTE:
The symbol nearby denotes that old equipment must
the tool dry completely before it is used again.
never be thrown away together with other waste (with the
TRANSPORTATION:
penalty of a fine).
Hazardous components of electronic
Store and transport the tool in its transport box to protect it against
equipment may adversely affect the natural environment and
humidity, dust penetration and small objects; remember to protect its
human health.
ventilation openings. Small objects after getting into the casing can
Each household may contribute to the recovery and reuse (recycling) of
result in damage to the motor.
old machinery and equipment. Both in Poland and Europe a system for
If the battery is removed for transport or storage, make sure the contacts
recovery of used equipment either exists or is being created. The system
will not short circuit. Remove metal items such as screws, nails, clasps,
obliges all organizations that sell such equipment to collect the used
loose bits, wires, or metal filings from the case or transport container or
machinery and appliances. Moreover, general purpose collecting points
otherwise prevent them from touching the battery.
for such equipment are available.
The policy of the PROFIX company consists in permanent improvements of the offered products and therefore the company
reserves the right to make amendments to the product specification without a prior notice. The images included into the
operation manual are only of the exemplary nature and may slightly differ from actual appearance of the device
purchased.
This
instruction
manual
is
protected by copyright.
Copying it
without the written consent of PROFIX Co. Ltd. is prohibited.
Содержание TJV10AL
Страница 52: ...www profix com pl ...
