Tryton THL2000C, Инструкция по эксплуатации

Страница: 5 / 36

5
plastics and fitting shrinking plastic tubing. It can be also used to soften DURING OPERATION:
adhesives and defrost water pipes.
n
Switching on/off
WARNING! The appliance is not intended to be operated by
means of an external timer or separate remote-control system.
Do not use the tool in professional applications. Any use in
applications other than indicated is prohibited and results in making the
warranty void and null and waiving manufacturer's liability for any
Temperature adjustment
resulting damage.
Any modification to the tool carried out by the user waives
manufacturer's liability for damage to the tool, user or other property.
The set includes:
ź
Hot air gun - 1 piece
ź
User's manual - 1 piece
ź
Warranty card - 1 piece
Tool components (see Fig. A ):
The numbering of tool components refers to graphics presented on page 2
of the user's manual:
Outlet nozzle
Work mode switch/selector
Power cord
Setting operation mode
TECHNICAL DATA:
The work mode switch/selector 9 can be set in two work positions (see
Fig. A ) .
The air flow and temperature required can be adjusted by using the table:
n
Noise emission information
NOTE: After changing from higher to lower temperature always allow the
Sound pressure value measured is lower than 70 dB (A).
tool to cool down.
BEFORE YOU START:
1. Make sure that power supply parameters meet the requirements
provided on the tool nameplate.
2. Make sure the tool switch is in off position. Connecting the tool to the
mains socket when its switch is in on position can result in serious
accident, as the hot air gun starts immediately.
3. When your workplace is too far to plug the tool directly to the mains
socket, use an extension cord with a cable cross-section meeting the
tool requirements. Extension cords should be as short as possible.
When in use extension cords must be fully uncoiled.
ź
To switch on, the work mode switch/selector 9 must be moved to
position I or II .
ź
To switch off, move the work mode switch/selector 9 to position O as
far as possible .
n
Temperature can be adjusted only in hot air mode II . The target
temperature can be adjusted using buttons 5 - 6 .
By gently pressing button 5 , the temperature can be lowered by 10 °C
n
until the minimum temperature level of 50 °C is reached.
By gently pressing button
6 , the temperature can be raised by 10 °C until
the maximum temperature level 650 °C is reached.
When the temperature setting is changed, heating or cooling of the air
n
stream takes place after a short time. During this time, the target
temperature is shown on display
2 between the flashing arrows. When
the target temperature is reached, the arrows turn off and the current
temperature is shown on the display.
1.
n
Air flow adjustment
2. Display
3. Save to memory button Buttons 7 - 8 allow air flow adjustment:
4. Programme selection button Pressing button 7 allows the air flow to be gradually reduced until the
minimum level is reached.
5. Operating temperature decrease button
The air flow should be reduced, for example, when the environment in
6. Operating temperature increase button
which the workpiece is located should not be heated too much or if the
7. Air flow decrease button
workpiece is light and the air flow could move it.
8. Air flow increase button
Pressing button 8 allows the air flow to be gradually increased until the
9.
maximum level is reached.
10.
11.
Heat shield
TYPES OF WORK:
n
n
Work mode I (cold air blowing)
The operation mode I is suitable for cooling down heated objects or for
drying a paint coat. It can be also used to cool the tool before putting in
storage or replacing its nozzle (spare nozzles not provided).
The air flow can be adjusted, the temperature is set to 50 °C (it cannot be
adjusted), work in programme mode is impossible.
n
Work mode II (warm air blowing)
In work mode II , the air flow and temperature can be adjusted; it is
possible to work in normal and programme mode.
When switching from cold air blowing to hot air blowing, the air flow,
temperature and possibly the programme automatically assume the
values
that were selected the last time hot air blowing was used.
n
Programme work mode
In programme work mode, it is possible to permanently store air flow
and temperature settings in one of four programmes. Each programme
Frequency 50/60 Hz
Power consumption 2000W
Operating temperature
50ºC
Voltage 220-240 V
Device class
Weight 0,9 kg
II
mode I
mode II
º ~ º
50 C 650 C
250l/min~500 l/min
Operation mode I
25 0 l/ min ~500l/ min - º 50 C
Operation mode II
25 0 l/ min ~500l/ min - ~
º º
50 C 650 C
Air flow