Tryton TFV12, Руководство по эксплуатации

Страница: 6 / 52

risk of damaging the battery cells.
IN USE:
n
Turning on/off
The switch ( 9 ) has fluid rotation speed adjustment built-in.
Auxiliary components
Press the switch to activate the power tool. The rotation speed will
increase the further the switch is pushed. To stop the power tool, release
the switch.
When the tool switch ( 9 ) is released the drill chuck is locked. It enables
quick, easy and convenient replacement of a working tool installed in the
drill chuck. To remove a drill (or a working bit) from the drill chuck, rotate
n
Choosing rotation direction ( see Fig. E )
the chuck ring anticlockwise to expand the opening of the chuck. Insert a
The driver can work with clockwise (right) or counter-clockwise (left)
new drill (or a working bit) into the chuck and rotate the chuck ring
rotation.
clockwise to secure the drill in the drill chuck.
- to select clockwise rotation, move the clockwise/counter-clockwise
Drills (or other working bits) must be moved to the full depth of the chuck
slider ( 4 ) to the left (looking from the back of the driver),
opening.
- to select counter-clockwise rotation, move the clockwise/counter-
Drilling boreholes
clockwise slider ( 4 ) to the right (looking from the back of the driver),
When the rotation direction switch is in the middle position, it is locked.
For drilling and driving screws in, clockwise operation should be
selected. For taking out the drill bit, removing a stuck drill bit, or
unscrewing screws, counter-clockwise operation should be selected.
n
Choosing torque ( see Fig. F )
The driver is equipped with a ring ( 2 ), which can be used for setting the
toque when driving screws. The ring has 22 settings, from 1 to 21 , and a
drilling setting.
Using a given setting (from 1 -
21 ) means that the clutch is set to an
assigned toque. This makes it possible to prevent a screw from being
Keep the drill aligned with the axis of the borehole. The drilling bit
driven too far or being damaged. Different torques should be used for
must be positioned perpendicularly to the surface of the machined
different screws and materials.
material. When the perpendicularity fails to be maintained the
Always start with a low torque and increase gradually until the desired
drilling bit may be seized or broken or, under extreme circumstances,
result is achieved.
the operator may be injured.
For drilling in metal, wood or plastic, set the ring ( 2 ), so that the indicator
Rotation speed of the drill spindle is controlled by the force the power
( 1 2 ) points to symbol ( 1 3 ) .
switch is depressed with.
see
n
Driving screws
It is recommended to drill the pilot borehole first. The pilot borehole must
be a little deeper and with a less diameter than the outer diameter of the
screw thread. When the screw is to be driven within the vicinity of the
material edge the pilot borehole prevents from undesired chipping of the
material.
If the screw is driven with abnormal difficulty the screw must be
retracted and the pilot borehole diameter should be enlarged.
Anyway, when problem to drive the screw in persists (e.g. in case of hard
wood grades) try to use a lubricating agent (e.g. liquid soap). Press the
tool to the screw with sufficient force to avoid spontaneous rotation of
the driving bit in the screw head. Use only those bits that accurately
n
ź
The practical fastener ( 6 ) can be used for attaching the drill-driver on
the user's belt, both for right-hand and left-hand dominant users.
ź
n
Battery capacity indicator
The battery capacity indicator ( 3 ) indicates the battery is empty with two
LEDs.
n
Work tool replacement
Green LED is lit:
The battery is fully charged.
Green and red LEDs are lit:
The battery is sufficiently charged.
Only red LED is lit:
The battery is empty, it needs charging.
n
2.
3.
4.
n
Changing the chuck ( Fig. G )
To free a seized bolt
hit is gently on its head.
screw counter-clockwise using a PH 2 screwdriver (No.2 Philips). For
the chuck not to rotate during screwing in the fixing screw, the chuck
should be held by the lower ring (the one closer to the drill/driver
body).
The drill/driver is equipped with an auxiliary light ( 1 0 ) for the area of
drilling/driving, which turns on after the appropriate switch ( 9 ) is
pushed.
CAUTION: Disconnect the battery from the driver or put the rotation
direction switch ( 4 ) in the middle position to secure the machine from being
started by mistake, which could in turn cause harm to the user.
1.
1. Disconnect the battery ( 7 ) from the driver.
2. Open the chuck as much as possible ( 1 )
3. Using a PH 2 (Philips No.2) screwdriver, rotate the fixing screw ( 14 ) of
the chuck clockwise ( CAUTION! L eft-thread ).
4. Hold the lower chuck ring (the one closer to the driver body) and
rotate the drill/driver chuck counter-clockwise (looking from the
point of view of the chuck).
CAUTION: A jammed keyless chuck ( 1 ) can be released by inserting the
short end of a hex key in the chuck and lightly tapping the longer arm of
the key (see Fig.
D ).
5. To attach the chuck, screw it onto the drive spindle counter-clockwise
(looking from the chuck side) and secure by screwing in the fixing
To drill deep boreholes carry out your job gradually, drill to lower
depths and remove the drill from the borehole from time to time to
remove borings from the borehole.
To drill large diameter boreholes it is recommended to start with
drilling a low-diameter borehole and then expand it to the desired
diameter. It prevents the tool from overloads.
When the drilling bit is seized during working switch immediately the
tool off to prevent it from being damaged. Switch the rotations
direction to the anticlockwise rotations and then remove the drilling
bit from the borehole.
match the bit head. When the screw head is damaged further driving the
screw in or out may prove infeasible.
6