background image

WARRANTY POLICY 

 
Under  the  warranty  your  C100  Chipper  is  warranted  for  2  year  from  the  date  of 
purchase  against  mechanical  defects,  faulty  workmanship  or  material.  90  days  for 
commercial  use.  This  warranty  covers  only  the  replacement, repair or  adjustment  of 
any part which fails as a result of a fault in manufacture or assembly. Defective parts 
will  be  repaired  or  replaced  without  charge  for  labour  or  materials  subject  to  the 
conditions detailed below.  
 
Warranty Exclusions, Limitations and Rights: 
 
1)  Any  failure  that  results  from  accident,  abuse  or  neglect  is  not  covered  by  this 

warranty 

2)  Transport  of  the  C100  Chipper  to  and  from  the  manufacturer,  their  agents  or 

dealers, to be paid for by the owner 

3)  Proof  of  purchase  date  must  be  provided  prior  to  the  commencement  of  the 

warranty work 

4)  Any failure of parts or material that is contributable to fair wear 
5)  Any  indirect  or  consequential  loss,  damage,  costs  or  expenses  suffered  by  the 

consumer that may result either directly or indirectly from the failure or malfunction 
of the product 

6)  Any repairs carried out  other than those by authorised Truyard agents or dealers 

cancel this warranty 

7)  Engine  warranty  is  separate  and  is  in  accordance  with  the  Engine  manufacturers 

express warranty 

 

TROUBLESHOOTING 

ISSUE 

CAUSE 

SOLUTION 

Irregular 
Chipping 

  Worn or damaged 

blades 

  Anvil not adjusted 

  Loose belts 

  Change blades or rotate them around 

180° 

  Adjust to within 1-2mm of chipper blade 

  Adjust the belts to the correct tension 

Excessive 
noise 

  Over tightened 

belts 

  Bearing  

  Loosen and inspect belt damage in case 

they need to be replaced 

  Replace the bearing  

Motor starts 
but mulcher 
doesn’t 

  Blockage in the 

flywheel 

  Remove the spark plug and make sure 

the flywheel is at a complete stop. Open 
the discharge chute and take out the 
blockage carefully. Test spinning the 
flywheel a full 360° to ensure that there 
aren’t more blockages. Be careful of the 
blades. 

Note: Truyard has available spare parts for the machine if a replacement is necessary 
 
 

Содержание Chipper

















Отзывы: