2
TECHNICAL CHARACTERISTICS:
Voltage:
220 V~
Frequency:
60 Hz
Current:
10 A
Speed:
3 450 RPM
Motor Rated Power:
3 Hp
Maximum Motor Power:
4 Hp
Maximum Pressure:
116 PSI
Tank Capacity:
63.4 Gal
IP Grade:
IP20
Air Flow:
7,7 CFM - 40 PSI
5,7 CFM - 90 PSI
Power Cord Grips Type:
Y
All conductors are:
1,5 mm
2
x 3C with 221 ºF Insulating
Temperature
Build quality:
Basic insulation.
Insulation quality:
Class l
Thermal insulation of motor winding:
Class B
To avoid risk of electrical shock or serious accident,
if power cord gets damaged it shall be repaired by the manufacturer
or by Truper® Authorized Service Center
Power cord grips used in this product: Type”Y”.
Assembly design in this product causes insulation to be affected
by liquid spills or splashing.
Before gaining access to terminals, all power
circuits shall be disconnected.
We do not recommend using power
cord extensions with compressors. Using that type of
extension cause power drops resulting in motor potency
loss and overheating. Instead of using an extension cord
increase the compressor’s action scope connecting a
longer hose into the outlet. Connect additional hose lengths
as needed.
BELT DRIVE AIR COMPRESSORS.
- Do not use compressed air to clean clothes.
- Do not apply compressed air directly to skin.
- Do not apply compressed air for breathing purposes unless
the air is filtered with a filter specifically for built to that
purpose.
- Do not use open-air piping. It could lash out and cause
injuries.
- Do not use flammable liquids to clean the compressor.
- Do not use an open fire to inspect inside the compressor or
the pressure deposit.
- Wear eye protection when using compressed air to clean the
unit.
- Use caution not to blow particles towards people: always use
an air gun for cleaning.
- Double-check all the auxiliary fixtures are functioning
adequately and have the right capacity for the application.
- Inspect regularly that all covers are fixed and firmly set.
- Replace all parts, tools and accessories when unfit for a safe
operation.
- Install a check-valve or a cut valve in the inlet piping in case
compressor shall be parallel coupled with a second
compressor or if it will be connected to an air supply system.
- Double-check all piping and hoses connected to the
compressor have the right diameter, and, adequate resistance
for the maximum pressure delivered by the compressor.
- Install the compressor making available an adequate
ventilation air supply towards the unit. Use care not to restrict
air ducts through the inlets in the cover and motor fan.
INSPECT:
Inspect the pumps’ rotation direction during the initial start up.
Verify any modification in the electric components’ or connections.
Turn off the compressor and disconnect from the power outlet.
Ventilate completely before disassembling any component or
making any maintenance service.
INSTALLATION AND VENTILATION
To service the compressor allow adequate access and free space
up and around the unit. It needs adequate protection against
weather. Good ventilation is essential. To gain maximum efficiency
admission air shall be as cold and clean as possible (a 37.4 ºF drop
in temperature will increase 1% the delivered air volume). Gas
impurities and particles, abrasive dust and corrosive gasses are
especially harmful. The exhaust vapors are hazardous if
compressed air is used to supply breathing devices.
Set the compressor as far away as possible from the work areas
to prevent from suctioning particles generated by the job (paint,
dust, etc.)
CONNECTION TO THE MAIN POWER SUPPLY
The compressor shall be set as close as possible to the main power
supply. Double-check the power supply matches the voltage
indicated in the motor nameplate.
This unit must be grounded.
The power cables are coded with the
following colors:
GREEN AND YELLOW GROUND
BLUE NEUTRAL
BROWN CURRENT
CAUTION
WARNING
WARNING
WARNING
CAUTION
WARNING
This unit SHOULD BE USED with
220 V~ to 240 V~ feeding
tension. Using a different
TENSION WILL
SEVERELY DAMAGE
the unit.
This tool is in compliance with
the Official Mexican Standard
(NOM - Norma Oficial Mexicana).
