Truck Hero Sentry Скачать руководство пользователя страница 1

Страница: 1 / 10

COMPONENTS

Driver Rail

Passenger Rail

Cover

Drill Guide

J-Nut

12X

10X

12X

Clamps

Tools Required:

T30 Torx drive

Drill

7.00 mm(9/32")
drill bit

Part# 1118565, Rev. A

OWNER'S MANUAL

Please read manual throughly before installing this kit.

Failure to install cover properly will void wrarranty.
- Use picture keys below to verify componets found in shipping

box and hardware bags.
- Damaged or missing parts? Call 1-877-878-9336 Mon - Fri 8 am-5

pm CT. Parts will be shipped to you factory direct. Do not return kit

to place of purchase.

Weather

Seal

Install the bulkhead seal supplied in the shipping box.

Bulkhead Seal

bulkhead on inside of

truck bed.

Position bulkhead seal

flush with the inside

edge of bulkhead.

Cab

FRONT (Cab)

WEATHER SEAL INSTALLATION FOR TRUCKS WITH AND WITHOUT TRAIL RAILS:

It is important that all areas where
the bed cover mounts are clean and
free of debris prior to installing.

Installation Parts Include:

Button head
M6 x 30MM

Page 1

TruXedo Inc.

•

2209 Kellen Gross Drive, Yankton, SD 57078

•

877-878-9336

•

truxedo.com

TruXedo Inc. 2020

Содержание Sentry











Результаты поиска

Содержание Sentry

Отзывы:

Похожие инструкции для Sentry

Бренды по названию

Популярные бренды

Truck Hero Sentry, Руководство пользователя

Результаты поиска

Содержание Sentry

Отзывы:

Похожие инструкции для Sentry

Бренды по названию

Популярные бренды