background image

Page 15

10. CREATE A TEMPORARY CODE

Temporary access for house sitter, contractor, cleaning company, etc. Use one of the 50 
available User Codes       and give it out for temporary access and delete it when it is no 
longer required. See steps 3 and 4 on page 13.  

11. RESTORE TO FACTORY SETTINGS

 (Make sure latch is retracted - unlocked) 

To reset the lock to the original factory settings including the Programming Code 
and all User Codes       remove one battery for 10 seconds. Reinsert the battery, hear a long 
and short beep, then immediately press       3 times within 3 seconds. The lock will 
beep and the light indicator will turn green.

12. VACATION MODE

With Vacation Mode enabled, the system enters into low-power consumption mode. During 
this mode, all buttons and functions including the remote control will be invalid until they are 
re-enabled (see steps below).

Enable:

Hear 1 beep and Light Indicator illuminates green then lock door

Disable:

To disable the Vacation Mode, you must press and hold        for more than 3 seconds, then 
input        to unlock the door. Vacation Mode is now disabled.

NOTE:

 If you only press the        for more than 3 seconds but do not input        the system 

will remain in Vacation Mode.

Attention:

When battery is under low voltage, the lock will give the (Low Battery Warning: Beeps and LED 
flashes red for 5 seconds). During this time your lock can still work. However once the voltage is lower 
than 4.3V (called Super-Low Voltage), the operation of the locking and unlocking will not work, user 
must replace batteries immediately. 

Audio and Visual Message Guide

Unlock / Valid programming:

Lock:

Invalid Programming:

Low Voltage:

Super Low Voltage:

4 Incorrect code entry attempts:

Power on:

Chip Reset:

Lock Error:

Repeat operation after Lock Error: 

1 long beep and LED illuminates green

2 short beeps and LED illuminates red

2 short beeps and LED flashes red twice

Beeps for 5 seconds (7/9 times depends on operation is unlock/lock)

4 short beeps and LED flashes red four times

2 short beeps and LED illuminates red each attempt

1 long beep and 1 short beep and LED illuminates green 

1 long beep and 1 short beep and LED illuminates green (may occur several times or once in a while)

3 long beeps LED flashes red three times

2 short beeps three times LED flashes red six times

UC

PC

UC

PC

10

PC

PC

1

Содержание 0711016


















Отзывы: