Troy-Bilt TRU CUT 100 Скачать руководство пользователя страница 15

Страница: 15 / 16

Tru Cut 100

Ref. No.

Part No.

Description

647-04014

Control Handle Assembly

710-1270

Oval C-Sunk Screw

712-0324

Hex Lock Nut

746-0883

Control Housing

720-0295

Foam Grip

749-0705A

Upper Handle

710-1205

Rope Guide

710-1174

Carriage Bolt

749-0928A

Lower Handle

10.

720-0279

Wing Nut

11.

720-0284

Hand Knob

12.

714-0104

Hairpin Clip

13.

746-0554

Control Cable 40.5”

15.

726-0240

Cable Tie

16.

17098

Hinge Clip

17.

731-04019

Trail Shield

18.

682-0139

Cutting Deck Assembly: 20”

19.

736-0105

Bell Washer

20.

720-0426

Knob: Height Adjustment

21.

732-0404

Lever: Spring

22.

734-04033

Wheel Assembly

23.

736-0504

Wave Washer

24.

738-0102

Axle Bolt

26.

738-0507B

Shoulder Bolt

27.

15262B

Pivot Bar

28.

682-3024

Handle Bracket Assy. RH

682-3025

Handle Bracket Assy. LH*

29.

738-0585

Stake Bolt

30.

732-0731

Torsion Spring

31.

14578

Height Adjust. Assembly RH

14579*

Height Adjust. Assembly LH

32.

782-7006

Mounting Bracket

33.

736-0270

Bell Washer

34.

710-0599

Self-tapping Screw

35.

710-0654A

Self-tapping Sems Screw

36.

731-1409

Chute Deflector

37.

682-7002

Mulching Plug Assembly

38.

712-0431

Hex Lock Nut

39.

15261A

Height Adjustment Plate

40.

731-1949

Cover: Front End

41.

748-0376C

Blade Adapter

753-0588

Blade Adapter Kit

42.

742-0740

20” Mulching Blade

43.

736-0524A

Blade Bell Support

44.

710-1044

Hex Bolt

45.

747-0710

Hinge Pin

46.

736-0451

Saddle Washer

Ref. No.

Part No.

Description

* Not shown in Illustration on previous page

NOTE:

For

painted parts

, please refer to the list of color

codes below. Please add the applicable color code, wherever
needed, to the part number to order a replacement part. For
instance, if a part numbered 700-xxxx is painted Red, the part
number to order would be 700-xxxx-0638.

Red: 0638; Black: 0637

Содержание TRU CUT 100

















Результаты поиска

Содержание TRU CUT 100

Отзывы:

Похожие инструкции для TRU CUT 100

Бренды по названию

Популярные бренды

Troy-Bilt TRU CUT 100, Руководство оператора

Результаты поиска

Содержание TRU CUT 100

Отзывы:

Похожие инструкции для TRU CUT 100

Бренды по названию

Популярные бренды