Troy-Bilt TB590 EC Скачать руководство пользователя страница 4

Страница: 4 / 24

INSTALL AND ADJUST THE HANDLE BAR

1. Place the handle bar between the top and middle clamp pieces (Fig. 1).
2. While holding the three pieces together, install the four (4) screws through

the top clamp and into middle clamp.

NOTE:

The holes in the top and middle clamp will line up only when

assembled correctly.

3. Place the clamps and the handle bar over the shaft housing and onto the

bottom clamp.

4. Hold each hex nut in the bottom clamp

recess with a finger. Start screws with a
large Phillips screwdriver. Do not tighten until
you make the handle bar adjustment.

5. While holding the unit in the operating position

(Fig. 22), position the handle bar to the location
that provides you the best grip.

6. Tighten the clamp screws evenly, until the

handle bar is secure.

REMOVE AND INSTALL THE CUTTING ATTACHMENT SHIELD

Remove the cutting attachment shield when using the unit as a
brushcutter

Remove the cutting attachment shield from the shield
mount by removing the three (3) screws with a flat blade
screwdriver (Fig. 5). Store parts for future use.

Install the cutting attachment shield when using the unit as a grass trimmer

Install the cutting attachment shield on the shield mount by inserting the three (3)
screws into the shield mount. Tighten securely with a flat blade screwdriver (Fig. 5).

REMOVE THE CUTTING ATTACHMENT AND
INSTALL THE CUTTING BLADE
NOTE:

To make cutting blade removal and

installation easier, place the unit on the
ground or on a work bench.

Remove the Cutting Attachment Shield

See Remove and Install the Cutting Attachment
Shield.

Remove the Cutting Attachment

1. Align the shaft bushing hole with the locking

rod slot and insert the locking rod into the
bushing hole (Fig. 6).

2. Hold the locking rod in place by grasping it

next to the boom of the unit (Fig. 7).

3. While holding the locking rod, remove the

cutting attachment by turning it clockwise off
of the output shaft (Fig. 8). Store the cutting
attachment for future use.

NOTE:

The blade retainer under the cutting

attachment will be used when installing the
cutting blade.

Install the Cutting Blade

4. Place the cutting blade on the output shaft

bushing (Fig. 9).

5. Make sure that the cutting blade is centered on the pilot step and sitting flat

against the output shaft bushing (Fig. 9).

6. Align the shaft bushing hole with the locking rod slot and insert the locking

rod into the bushing hole (Fig. 6).

7. Put the blade retainer and nut on the output shaft (Fig. 9). Make sure that

the blade is installed correctly.

8. Tighten nut counterclockwise against the blade while holding the locking

rod (Fig. 10):

• If using a torque wrench and a 13 mm socket tighten to:

325 - 335 in•lb, 27 - 28 ft.•lb, 37 - 38 N•m.

• Without a torque wrench, use a 13 mm closed-end or socket wrench,

turning the nut until the blade retainer is snug against the shaft bushing.
Make sure that the blade is installed correctly, then rotate the nut an
additional 1/4 to 1/2 turn counterclockwise (Fig. 10).

9. Remove the locking rod from the locking rod slot.

ASSEMBLY INSTRUCTIONS

WARNING:

To prevent serious

personal injury, never operate the unit as a
trimmer without the cutting attachment
shield in place.

Cutting Attachment

Shield

Shield Mount

Fig. 5

Screws (3)

Locking

Rod Slot

Bushing Hole

Output Shaft

Bushing

Locking

Rod

Fig. 6

Fig. 7

Cutting Attachment

Fig. 8

Nut

Fig. 9

Output

Shaft

Blade

Retainer

Pilot Step

KNOW YOUR UNIT

WARNING:

The cutting attachment shield should NOT be installed

when operating the unit with a blade. Remove the cutting attachment shield
before removing or installing the blade.

DANGER:

The gear housing gets hot

with use. It can result in injury to the
operator. The housing remains hot for a
short time even after the unit is turned off.
Do not touch the gear housing until it has
cooled.

DANGER:

If the cutting blade is off-

center, the unit will vibrate and the blade
may fly off, causing possible serious
personal injury.

WARNING:

To avoid serious personal injury or damage to the unit, do

not start or operate this unit with the locking rod in the locking rod slot.

WARNING:

Do not sharpen the cutting blade. Sharpening the blade

can cause the blade tip to break off while in use. This can result in severe
personal injury. Replace the blade.

INSTALL THE HARNESS

1. Push the strap through the center of the buckle.
2. Pull the strap over the cross bar and down through the slot in the buckle (Fig. 2).
3. Put the harness on over head and onto shoulder.

Snap it on to the support fitting (Fig. 3).

4. Adjust length to fit the operator’s size. Pull tab to

lengthen, pull strap to shorten (Fig. 4).

Fig. 2

Support Fitting

Fig. 3

Fig. 4

Cutting Attachment Shield

Fuel Cap

Throttle Control

Bullhorn Handle

Cutting Attachment