manualshive.com logo in svg

Troy-Bilt TB227 XP, Руководство оператора

Поделиться
Скачать
Troy-Bilt TB227 XP Скачать руководство пользователя страница 17

17

REPLACING THE BLADE 

Removing the Blade 
1. Rotate the blade (Fig. 28) until the shaft bushing hole aligns with 

the locking rod slot (Fig. 26). 

2. Insert the locking rod through the locking rod slot and into the 

shaft bushing hole (Fig. 26). 

3. Hold the locking rod in place (Fig. 27). 
4. While holding the locking rod in place, unscrew the nut by turning 

it clockwise with a wrench (Fig. 27). 

5. Remove the locking rod (Fig. 28). 
6. Remove the blade retainer and blade (Fig. 28). 

Installing the Blade 
1. Rotate the output shaft bushing until the shaft bushing hole 

aligns with the locking rod slot (Fig. 26). 

2. Insert the locking rod through the locking rod slot and into the 

shaft bushing hole (Fig. 26). 

3. Hold the locking rod in place (Fig. 27). 
4. While holding the locking rod in place, put the blade on the 

output shaft bushing (Fig. 29). 

5. Place the blade retainer on the output shaft with the flat surface 

against the blade (Fig. 29). 

6. Screw the nut onto the output shaft (Fig. 29). 
7. Tighten the nut counterclockwise with a wrench (Fig. 30): 

• If using a torque wrench, torque to: 

325 - 335 in•lb, 27 - 28 

ft.•lb, 37 - 38 N•m. 

• If using a closed-end or socket wrench, turn the nut until the 

blade retainer is snug against the blade. Make sure the blade 

is installed correctly, then rotate the nut an additional 1/4 to 

1/2 turn counterclockwise. 

8. Remove the locking rod.

WARNING:

 To avoid serious personal injury, always 

wear gloves when handling the blade.

WARNING:

 To avoid serious personal injury or damage 

to the unit, do not start or operate the unit with the locking 

rod inserted into the locking rod slot.

Fig. 26

Fig. 28

Shaft Bushing Hole

Blade Retainer

Output Shaft 

Bushing

Locking Rod

Locking Rod Slot

Nut

Blade

Locking Rod

Fig. 27

Nut

WARNING:

 To avoid serious personal injury, make sure 

that the pilot hole on the blade is sitting flat against the 

output shaft bushing (Fig. 29). The unit will vibrate and the 

blade may fly off if the blade is not centered.

Fig. 29

Blade Retainer

Nut

Blade

Output Shaft 

Bushing

Pilot Hole

Output Shaft

Fig. 30

Содержание TB227 XP

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды