background image

S

ECTION

 5— O

PERATION

18

Driving The Tractor

WARNING! 

Avoid sudden starts, excessive speed 

and sudden stops. 
 

1. 

Release the parking brake. Move the throttle/choke control 

lever into the FAST 

 position.

2. 

To travel FORWARD, slowly press the forward drive pedal   
forward until the desired speed is achieved. See Figure 5-2.

Forward Drive Pedal

Reverse Drive Pedal

Parking Brake/Cruise Control Lever

Figure 5-2

3. 

To stop or slow down the tractor, take your foot off of the 

forward   or reverse drive pedal  . To lock the parking 
brake, press forward on the brake pedal, then press down 
on the parking break/cruise control lever and then release 
the brake pedal 

.

4. 

To use the cruise control:

a. 

Press down on the forward drive pedal  .

b. 

While maintaining the desired speed press down on 
the parking break/cruise control lever then release 

the forward drive pedal   to activate the cruise 
control.

5. 

To release the cruise control, press the brake 

 or the 

forward drive pedal  .

NOTE: 

The forward   and reverse drive pedals   must not 

be used when the brake is partially engaged. When the 
brake is locked the drive belt is disengaged but if the brake 
is only part way back then the brakes are engaged but so 
is the drive belt so transmission damage will occur if you 
push forward or reverse.

6. 

To travel in reverse, check that the area behind is clear then 

slowly push forward on the reverse drive pedal   with the 
ball of your foot (NOT your heel) until the desired speed is 
achieved. See Figure 5-2.

CAUTION: 

Do NOT attempt to change the 

direction of travel when the tractor is in motion. 
Always bring the tractor to a complete stop before 
moving the tractor from forward to reverse or vice 
versa.

WARNING! 

Do not leave the seat of the tractor 

without first placing the PTO knob in the 
disengaged (OFF) position and engaging the 
parking brake. If leaving the tractor unattended, also 
turn the engine off and remove the ignition key.

Reverse Caution Mode

The REVERSE CAUTION MODE 

 position of the ignition 

switch module allows the tractor to be operated in reverse with 
the blades (PTO) engaged.

NOTE: 

Mowing in reverse is not recommended.

WARNING! 

Use extreme caution while operating 

the tractor in the REVERSE CAUTION MODE 

Always look down and behind before and while 
backing. Do not operate the tractor when children 
or others are around. Stop the tractor immediately if 
someone enters the area.

To use the REVERSE CAUTION MODE 

:

NOTE: 

The operator MUST be seated in the tractor seat.

1. 

Start the engine as instructed on the previous page.

2. 

Turn the key from the NORMAL MOWING 

 (Green) 

position to the REVERSE CAUTION MODE 

 (Yellow) 

position of the key switch module. See Figure 5-3.

Indicator 

Light

Reverse 

Push Button

Stop 

Position

Start 

Position

Reverse 

Caution Mode 

Position

Figure 5-3

Содержание Pivot S









































































Отзывы: