Troy-Bilt 24B-060F766 Скачать руководство пользователя страница 9

9

4

WARNING

Never run the engine 

indoors or in a poorly 

ventilated area. Engine 

exhaust contains 

carbon monoxide, an 

odorless and deadly 

gas.

WARNING: The operation of any 
chipper shredder can result in foreign 
objects being thrown into the eyes, 
which can damage your eyes se-
verely. Always wear the safety glasses 
provided with this unit or eye shields 
while operating or while performing any 
adjustments or repairs.

Gas and Oil Fill-Up 

1.  Check oil level and add oil if necessary. Follow engine 

manual for this. See Figure 7 for location of the oil fill.

2.  Service the engine with gasoline as instructed in the 

engine manual.  See Figure 7 for location of gas fill.

WARNING: Never fill fuel tank indoors 
with engine running or until the engine 
has been allowed to cool for at least two 
minutes after running.

Starting Engine

IMPORTANT

: The bag/chute switch button must be fully 

depressed by the tip of front tab on bag handle or blower 
chute for engine to start.

1.  Attach spark plug wire to spark plug. Make certain 

the metal cap on the end of the spark plug is fastened 
securely over the metal tip on the spark plug.

2.  Make sure safety switch wire is connected to engine 

and properly grounded to mounting bracket.

3. 

Engines with choke lever:

  Move choke lever on engine to CHOKE position. (A 

warm engine may not require choking).

  Engines with primer:

  Prime engine as instructed in separate engine manual.
4.  The throttle control lever is located on the engine. 

Move engine throttle control lever to FAST or START 
position. See Figure 8.

5.  Grasp starter handle and pull rope out slowly until 

engine reaches start of compression cycle (rope will 
pull slightly harder at this point).

6.  Pull rope with a rapid, continuous, full arm stroke. 

Keep a firm grip on starter handle. Let rope rewind 
slowly.

7.  Repeat the previous steps until engine fires. When 

engine starts, move choke control (if equipped) 
gradually to RUN position. 

WARNING: Never run the engine 
indoors or in a poorly ventilated area. 
Engine exhaust contains carbon 

monoxide, an odorless and deadly 
gas. 

Stopping Engine 

1.  Move throttle control lever to STOP or OFF position.
2.  Disconnect spark plug wire from spark plug and 

ground against the engine.

NOTE

: See your engine manual packed with your unit 

for more detailed instructions.

Operating 

Your Yard 

Vacuum

����

Figure 8

Never fill fuel tank 
indoors with engine 
running or until the 
engine has been 
allowed to cool for at 
least two minutes after 
running. 

Содержание 24B-060F766





















Отзывы: