Troy-Bilt 12A-E753B063 Скачать руководство пользователя страница 16

Страница: 16 / 22

Servicing the Troy-Bilt Wide Cut 33” Combination Mower

13.9. Using a shop rag to protect your hand, hold the

blade secure while removing the flange lock
screw that secures the left spindle shaft with an
air gun and 5/8 inch socket. See Figure 47.

13.10.Remove the cutting blade and spindle shaft from

the left spindle housing.

NOTE:

There will be a lock washer and flat

washer securing the drive pulley to the blade
spindle.

13.11. Remove the drive pulley from the top of the

cogged pulley.

NOTE:

There will be a spacer between the drive

pulley and the cogged pulley assembly. See Fig-
ure 48.

13.12.Removed the cogged pulley assembly and spe-

cial thrust washer from the top of the Spindle
assembly.

13.13.Using a ½ inch socket, loosen the four mounting

bolts securing the spindle housing to the deck.
See Figure 49.

NOTE:

Hold the housing from underneath the

deck when removing the final mounting bolt.
Remove the housing from the deck.

13.14.Inspect the housing for excessive wear or dam-

age and replace as needed.

13.15.Assembly is the reverse order of disassembly.

IMPORTANT:

Torque the spindle housing flange

lock screws to 15 foot pounds during reassem-
bly.

IMPORTANT:

During assembly, place Locktite

242 on the threads of the spindle shaft screw
and torque to 35 ft. lbs.

IMPORTANT:

Time the blades properly during

reassembly. Set the cutting blades perpendicular
to each other during installation of the toothed
drive belt. Torque the blade mounting screw to
35 ft. lbs.

14.

TRANSMISSION REMOVAL

14.1. Remove the blade drive belt (see the Blade

Drive Belt Removal section)

14.2. Remove the wheel drive belt (see the Wheel

Drive Belt Removal section)

NOTE:

While it may be possible to remove the

transmission while the deck is installed, it would
be easier to first remove the deck.

14.3. Support the frame off the ground in a way that

allows you to work on the transmission from

Figure 47

HOLD BLADE FROM BELOW

Left Drive Pulley

Figure 48

Cogged Pulley

Drive Pulley

Spacer

Flat Washer

Lock Washer

Screw

Special Thrust Washer

Figure 49

Spindle Mounting Bolts (4)

Содержание 12A-E753B063























Результаты поиска

Содержание 12A-E753B063

Отзывы:

Похожие инструкции для 12A-E753B063

Бренды по названию

Популярные бренды

Troy-Bilt 12A-E753B063, Руководство по обслуживанию

Результаты поиска

Содержание 12A-E753B063

Отзывы:

Похожие инструкции для 12A-E753B063

Бренды по названию

Популярные бренды