Troxler 3411-B Скачать руководство пользователя страница 69

Страница: 69 / 109

Model 3400-B Series

Appendix A-9

3411-B Error Codes

Error

Code

Indicated Failure

Mode

Probable Cause

System failed internal

test condition.

Microprocessor memory board

hardware failure.

Accumulated number

exceeds display size.

Position of PWR/TIME switch

was changed during

accumulation OR hardware

failure on I/O board.

10,

Bad keyboard input.

Two keys depressed, defective

keyboard or hardware failure

on I/O board.

Microprocessor tried to

evaluate the log of a

negative number.

Incorrect depth selected by

DEPTH switch.

Microprocessor

attempted to divide by

zero.

No standard counts in the MS

or DS registers.

Negative overflow in

division.

Incorrect depth selected by

DEPTH switch OR standard or

measure counts are not valid.

Positive overflow in

division.

Same as above.

Invalid input from

MOISTURE

CORRECTION switches.

Switch failure, I/O board

failure, or operator induced

error during chain calculations.

Invalid input from

DEPTH switch.

Same as above.

Содержание 3411-B














































































































Результаты поиска

Содержание 3411-B

Отзывы:

Похожие инструкции для 3411-B

Бренды по названию

Популярные бренды

Troxler 3411-B, Руководство по эксплуатации и инструкции

Результаты поиска

Содержание 3411-B

Отзывы:

Похожие инструкции для 3411-B

Бренды по названию

Популярные бренды