14
EN
monobloc air conditioner without external unit PAC-W 2600 SH
WiFi connection
Proceed as follows to establish a WiFi connection:
ü
The device is now in standby mode.
1. Download the Trotec Assistent App and open it on a
smartphone.
2. Select
Add Device
by pressing the + sign in the top right
corner.
3. Select
Large household appliances
and
Air conditioning
(Wi-Fi)
among them.
4. Press the
fan speed
button (18) on the control panel of the
device for approx. 3 s.
ð
The
Wifi
LED (22) lights up.
5. Press the
fan speed
button (18) again on the control panel
of the device for approx. 3 s.
ð
The
Wifi
LED (22) flashes approx. 2 times per second.
ð
The device is in
Quick Connect
mode.
6. Follow the instructions of the app on the smartphone.
ð
Once the
Wifi
LED (22) is permanently illuminated, the
connection is established.
Info
If the WiFi connection is interrupted, the device may
not automatically reconnect to the network. If this is
the case, re-establish the connection with the
fan
speed
button (18).
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
•
Switch off the device.
•
Hold onto the mains plug while pulling the power cable out
of the mains socket.
•
Clean the device according to the Maintenance chapter.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The device does not start:
•
Check the power connection.
•
Check the power cable and mains plug for damages.
•
Check the on-site fusing.
•
Observe the operating temperature according to the
chapter Technical annex.
•
Wait for 10 minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device works with reduced or no cooling capacity:
•
Check whether
cooling
mode is selected.
•
Check the position of the ventilation flaps. They should be
opened to the maximum.
•
Check the air filter(s) for dirt. If necessary, clean or replace
the air filter(s).
•
Check whether any windows and/or doors of the room are
open. If so, close them.
•
Check the temperature setting at the device. Reduce the
set temperature if it is higher than the room temperature.
Condensate is leaking:
•
Check the device for leaks.
The compressor does not start:
•
Check whether the overheating protection of the
compressor has tripped. Disconnect the device from the
mains and let it cool down for approx. 10 minutes before
reconnecting it.
•
Check whether the ambient temperature equals the target
temperature (in
cooling
mode). The compressor will not
switch on unless the respective temperature is reached.
•
The compressor may start up with a delay of 3 minutes, as
it is provided with an internal protection against direct
restart.
The device gets very warm, is loud or is losing
performance:
•
Check the air inlets and air filters for dirt. Remove external
dirt.
•
From the outside, check the device for dirt (see chapter
Maintenance). If the inside of the device is dirty, have it
cleaned by a specialist company for cooling and air-
conditioning or by Trotec.
The device does not respond to the infrared remote control:
•
Check whether the distance between remote control and
device is too large and reduce it if necessary.
•
Make sure there are no obstacles, such as furniture or
walls, between the device and the remote control. Ensure
visual contact between device and remote control.
•
Check the charging status of the batteries and change
them if required.
•
If the batteries have just been changed, check them for
correct polarity.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
The device still does not operate correctly after these
checks:
Please contact the customer service. If necessary, bring the
device to a specialist company for cooling and air-conditioning
or to Trotec for repair.
