background image

15

EN

oil heater IDX 30 D

Adjusting the air pressure for the pump

Ideally, the air pressure should range between 0.32 bar and
0.36 bar. During operation, the air pressure can be read from
the pressure gauge (5).

Info

If the air pressure exceeds 0.36 bar, a flame emerges
from the air outlet of the device. The device then stops
running.
If the pressure is lower than 0.32 bar, the device
continues to operate, but with a reduced performance.

1. Adjust the air pressure during operation by means of a

slotted screwdriver. For lowering turn the screw counter-
clockwise; for increasing carefully turn it clockwise.

0,6

0,8

1

0

0,2

0,4

Technical annex

Technical data

Parameter

Value

Article number

1.430.000.066

Method of heating

direct

Amount of air

735 m³/h

Fan

Axial fan

Mains connection

1/N/PE~220–240 V / 50 Hz

Nominal heat output

30 kW (25,800 kcal)

Temperature increase ΔT

90 °C (1.5 m distance)

Input voltage

230 V / 50 Hz

Current consumption

0.8 A

Max. fuel consumption

2.9 l/h

Sound level (distance 1 m)

65 dB(A)

Weight

20 kg

Dimensions 
(length x width x height)

388 x 942 x 460 (mm)

Minimum distance to walls or
other objects

3 m

Fuels

The following fuels are approved for the device:

EL fuel oil

Kerosene

Diesel

Содержание IDX 30 D























Отзывы: