Tropos Networks 7320 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 100

background image

Chapter 1

Tropos 7320 Router Installation Guide

5

Installation Hardware and Tools

Tropos Networks provides the following accessories to install the Tropos 7320 router:

One pole bracket

One sun shield

Two 4-inch diameter hose clamps

Four 6-inch diameter hose clamps

Five 5/16-inch #10-32 stainless steel hex head machine screws

You must supply the following tools:

5/16-inch nut driver

1/4-inch flat blade screwdriver

Tower mounting only: supply stainless or galvanized steel channel stock and 1/2-inch or

5/8-inch nuts, bolts, and washers to connect to the tower arm.

Wood pole mounting only: two 1/4-inch diameter, 3 1/2-inch long lag bolts

Site Planning

To ensure safe and durable wiring, installation of the Tropos 7320 router must follow
appropriate electrical and building codes. Follow the National Electrical Code (NEC)
requirements, unless local codes in your area take precedence over the NEC code.

The following distance limits apply to installations that have 10/100 Base-T Category 5 network
cables attached to the Tropos 7320 router:

300 feet maximum between devices for 100BaseT operation

500 feet maximum for 10BaseT operation.

The Ethernet duplex and speed setting is configurable.

Note

National Electrical Codes (NEC) Article 800 requires the use of Agency Listed (UL/CSA/TUV) Building
Entrance Protector for all power and data communications cables entering a building. The NEC intends by
Article 800 to protect the building and occupants from fires caused by transient voltage and current surges.

Note

Ethernet data cable installations having lengths greater than 140 feet in the outdoor environment must use
a UL497 approved (UL/CSA/TUV Listed) primary protection device at the building entrance. Ethernet data
cable installations having lengths less than 140 feet in the outdoor environment may use a UL497A (UL/
CSA/TUV Listed) secondary protection device at the building entrance. Tropos Data Protection Device and
Network Protection Units are UL497A secondary protection devices.

«
...
15
16
17
18
19
...
»

Содержание 7320





































































































Отзывы:

Нет отзывов

Похожие инструкции для 7320

AirPlus DWL-810

Бренд: D-Link Страницы: 25

Бренд: NEC Страницы: 8

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Magic WiFi mini Ek

Бренд: Devolo Страницы: 22

Бренд: Keithley Страницы: 98

Бренд: XtendLan Страницы: 228

Бренд: TP-Link Страницы: 7

Speed Touch 591s

Бренд: Alcatel Страницы: 184

COMMWARE ECHO 5G

Бренд: pivotal Страницы: 2

Бренд: Cowfish Technologies Страницы: 38

Sinus 154 data II

Бренд: T-COM Страницы: 12

Бренд: Idis Страницы: 22

Бренд: QTech Страницы: 406

Бренд: US Robotics Страницы: 180

Бренд: Aviosys Страницы: 77

Бренд: DHD Power Cruiser Страницы: 60

Бренд: MCT Страницы: 12

IntraSwitch 5324MT

Бренд: Asante Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды