R9T12FIRE
Page 12 of 16
Rev. H 06SEP17
FIRE PIT NATURAL GAS CONVERSION AND OPERATING
INSTRUCTIONS
First turn the LP Gas tank (if installed) fully off by rotating the valve completely to the left until
closed. Then disconnect the LP Gas tank hose with built in regulator (shown in blue) by turning
the large connector (shown in black) fully counter-clockwise until the hose is completely
disconnected.
The proper pressure and gas type must be checked prior to installation. A 1/8” NPT test port is
provided at the burner assembly connection beneath the burner tray. When converting from LP
to Natural gas, installer must remove the supplied gas hose and LP regulator and install the
correct regulator for Natural gas. The regulator must limit the supply as specified below:
Natural Gas:
•
Supply Pressure:
•
Minimum 5.0” WC (water column), Maximum 10.0” WC
•
Operating Pressure:
•
Minimum 5.0” WC, Maximum 7.0” WC
Remove the LP Gas tank hose from the gas valve (shown in bronze) at the elbow (or straight
connector) coming out of the gas valve as shown above. Connect your inlet supply line,
including pressure regulator to this location. Follow all local codes. Do not install without a
regulator, which will limit your fuel supply to 5 inches of water column.
R9T12FIRE
Page 12 of 16
Rev. H 06SEP17
FIRE PIT NATURAL GAS CONVERSION AND OPERATING
INSTRUCTIONS
First turn the LP Gas tank (if installed) fully off by rotating the valve completely to the left until
closed. Then disconnect the LP Gas tank hose with built in regulator (shown in blue) by turning
the large connector (shown in black) fully counter-clockwise until the hose is completely
disconnected.
The proper pressure and gas type must be checked prior to installation. A 1/8” NPT test port is
provided at the burner assembly connection beneath the burner tray. When converting from LP
to Natural gas, installer must remove the supplied gas hose and LP regulator and install the
correct regulator for Natural gas. The regulator must limit the supply as specified below:
Natural Gas:
•
Supply Pressure:
•
Minimum 5.0” WC (water column), Maximum 10.0” WC
•
Operating Pressure:
•
Minimum 5.0” WC, Maximum 7.0” WC
Remove the LP Gas tank hose from the gas valve (shown in bronze) at the elbow (or straight
connector) coming out of the gas valve as shown above. Connect your inlet supply line,
including pressure regulator to this location. Follow all local codes. Do not install without a
regulator, which will limit your fuel supply to 5 inches of water column.
R9T12FIRE
Page 12 of 16
Rev. H 06SEP17
FIRE PIT NATURAL GAS CONVERSION AND OPERATING
INSTRUCTIONS
First turn the LP Gas tank (if installed) fully off by rotating the valve completely to the left until
closed. Then disconnect the LP Gas tank hose with built in regulator (shown in blue) by turning
the large connector (shown in black) fully counter-clockwise until the hose is completely
disconnected.
The proper pressure and gas type must be checked prior to installation. A 1/8” NPT test port is
provided at the burner assembly connection beneath the burner tray. When converting from LP
to Natural gas, installer must remove the supplied gas hose and LP regulator and install the
correct regulator for Natural gas. The regulator must limit the supply as specified below:
Natural Gas:
•
Supply Pressure:
•
Minimum 5.0” WC (water column), Maximum 10.0” WC
•
Operating Pressure:
•
Minimum 5.0” WC, Maximum 7.0” WC
Remove the LP Gas tank hose from the gas valve (shown in bronze) at the elbow (or straight
connector) coming out of the gas valve as shown above. Connect your inlet supply line,
including pressure regulator to this location. Follow all local codes. Do not install without a
regulator, which will limit your fuel supply to 5 inches of water column.
K
305251_R9T12FIRE.indd 12
9/14/17 2:18 PM
