6
E
Instructions
• Read the operating instructions before use.
• The pet feeder is not a toy for children. Do not let children play
with the packaging foil. Danger of suffocation!
• The feeder is only suitable for dry food (diameter 5 - 15 mm).
• Do not use it with puppies and kittens under 7 months.
• The base unit must not get wet - not dishwasher safe.
• Additional instructions for the use of IOT devices can be found
at the end of this manual.
Electric Shock Hazard!
• Incorrect use may result in electric shock.
• The mains voltage of the socket must match the specification
on the automatic feeder.
• Ideally, use an easily accessible socket so that you can quickly
disconnect the feeder from the mains if necessary.
• Do not use the feeder if there is visible damage to the appliance
or the mains cable or plug.
• Do not open the feeder, but contact our customer service.
• Do not use a timer or other remote control system.
• Never touch the mains plug with wet hands.
Safety:
• The feeder is suitable for indoor use only.
• Place the feeder on a level surface. The feeder must be suffici-
ently ventilated on all sides.
• Only use the feeder with the feed container and lid and do not
place anything on top of it.
• Never pull the mains plug out of the socket by the cable, always
grasp the mains plug.
• Do not use the power cord as a carrying handle.
• Keep the feeder and power plug away from open flames and heat.
• Route the power cord so that it does not become a tripping
hazard.
• Do not kink the power cord or place it over sharp edges.
• Do not allow your pet to nibble on the feeder or cord. If neces-
sary, protect it with a cord protector.
• Never reach for an electrical appliance if it has fallen into the
water. In such a case, unplug the appliance immediately.
• Unplug the feeder when not in use or when cleaning it.
Preparation:
1. Connect the automatic feeder to a power source using the
power plug. Switch on the main switch at the bottom.
2. To control and program the automatic feeder, now download
the "Tuya Smart" app to your cell phone or tablet. Scanning the
QR code will take you directly to the download:
3. Optionally, you can insert 3 x D mono batteries into the auto-
matic feeder as an emergency power supply. The programmed
feeding times can thus be guaranteed even in the event of a
power failure. Please note that the automatic feeder cannot be
accessed via the app in emergency mode.
Registrierung:
Open the app and click REGISTER to create an account.
Pairing the device:
The next step is to connect the automatic feeder to the Internet
and pair it with your smartphone. Please be sure to follow these
instructions to ensure smooth pairing:
1. The automatic feeder should be placed near your WLAN router
for the duration of the pairing process. At the same time, your
smartphone should be in the immediate range of the automatic
feeder.
2. Make sure that your smartphone is connected to the WLAN and
has a high signal strength.
3. Two different pairing methods are available to pair the device:
EZ mode and AP mode. EZ mode works exclusively in pure 2.4
GHz networks. The AP mode, on the other hand, also works
with modern dual-band routers that broadcast 2.4 GHz and 5.0
GHz parallel. We recommend pairing in AP mode.
4. Please note that the feeder does not work in 5.0 GHz-only
networks.
5. If your WLAN password contains special characters, there
may be problems with the pairing process. Change your Wi-Fi
password so that it contains only letters and numbers. The
maximum length of the WLAN password is 20 characters.
AP mode (recommended):
1. Reset the feeder by pressing and holding the SET button on
the top of the unit for 5+ seconds. An audible signal will sound
to confirm and after approximately half a minute, the green
indicator light (LINK) should begin to flash rapidly. (approx. 1 ×
per second)
Note: Please contact customer service([email protected])
if you do not hear a beep and the green indicator light does not
start flashing after the reset.
2. Now press the SET button 11 × quickly in succession to activate
the hotspot for pairing in AP mode. An acoustic signal confirms
the activation and after about half a minute, the green indica-
tor light (LINK) should start flashing slowly. (approx. 1 × every
3 seconds) If the indicator light continues to flash rapidly, the
activation of the hotspot has not worked properly. In this case,
repeat this step. Please make sure to press the SET key quickly
and evenly!
3. In the app, select ADD DEVICE, and then select SECURITY
CAMERA (Wi-Fi) in the VIDEO MONITORING device category.
4. On the following page, select Wi-Fi MODE from the drop-down
menu in the upper right corner. Tap NEXT and select the AP
MODE.
Note: The default pairing method "QR code" does not work
with TX Smart feeders.
5. Enter your WLAN access data on the following page. Tap NEXT.
Please note that the WLAN password must not contain any
special characters.
Содержание TX8 Smart
Страница 51: ...51 ...
