background image

Triton Showers 

Triton Road 

Nuneaton 

Warwickshire  CV11 4NR

Triton is a division of Norcros Group (Holdings) Limited

TRITON reserve the right to change product specification without prior notice. E&OE. © TRITON SHOWERS 201

6

Fax: 02476 324504

www.tritonshowers.co.uk

E-mail: [email protected]

Extended Warranty AVAILABLE NOW. Call 02476 378495 for more details.

TRITON STANDARD GUARANTEE

With the exception of accessories, Triton guarantee the 
product against all manufacturing defects for a period of

2 years

 (for domestic use only) from the date of purchase, 

provided that it has been installed by a competent person in 
full accordance with the fitting instructions.

All accessories such as shower heads, hoses and riser rails 
carry a 

1 year

 parts only guarantee against manufacturing 

defects.

Any part found to be defective during this guarantee period 
we undertake to repair or replace at our option without 
charge so long as it has been properly maintained and 
operated in accordance with the operating instructions, and 
has not been subject to misuse or damage. This product 
must not be taken apart, modified or repaired except by a 
person authorised by Triton. This guarantee applies only to 
products installed within the United Kingdom and does not 
apply to products used commercially. This guarantee does 
not affect your statutory rights.

What is not covered: 

15

-

1

2

-16

UK SERVICE POLICY

In the event of a product fault or complaint occurring, the following 

procedure should be followed:

1.

Telephone Customer Service on 

024 7637 2222

 having available, 

 

your details including post code, the model number and power 

 

rating of the product, together with the date of purchase and, where

 

 

applicable, details of the particular fault.

2.

If required, the Customer Service Advisor will arrange

 

for a qualified engineer to call.

3.

All products attended to by a Triton service engineer must be 

installed in full accordance with the Triton installation guide 

applicable to the product. (Every product pack contains an 

installation guide, however, they can also be bought via our 

Customer Service Spares Department).

4.

Our engineer will require local parking and if a permit is required this 

must be available to the engineer on arrival at the call.

5.

It is essential that you or an appointed representative (who must be 

over 18 years of age) is present for the duration of the service 

engineer's visit. If the product is in guarantee you must produce proof 

of purchase.

6.

Where a call under the terms of guarantee has been booked and the 

failure is not product related (i.e. scaling and furring, incorrect water 

pressure, pressure relief device operation or electrical/plumbing 

installation fault) a charge will be made. A charge will also be issued if 

nobody is at home when the service engineer calls or adequate 

parking/permit is not available.

7.

If the product is no longer covered by the guarantee an up front 

fixed fee will be charged before the site visit.

8.

Should proof of purchase not be available on an “in-guarantee” call, 

or should the service engineer find that the product is no longer 

under guarantee, the engineer will charge the same fixed price and 

the customer will be expected to pay the engineer before he leaves. If 

payment is not made on the day an administration charge will be 

added to the fixed charge.

9.

If a debt is outstanding from a previous visit, or from any other Triton 

purchase, Triton reserves the right to withhold service until the debt 

has been settled.

10.

 Triton takes the health, safety and wellbeing of its employees very 

seriously and expects customers to treat all staff members with 

respect. Should any employee feel threatened or receive abuse, either 

verbally or physically, Triton reserves the right to withhold service

Replacement Parts Policy

Availability:

 It is the policy of the manufacturer to maintain parts 

availability for the duration of production and a period of five years 

thereafter, in accordance with industry standards.
Spare parts are available via our website, www.tritonshowers.co.uk, or by 

telephoning Triton Customer Service Spares Department. Payment should 

be made by credit/debit card (excluding American Express or Diners 

Card). Payment can also be made by pre-payment of a pro forma invoice 

by cheque or money order.
Telephone orders are based on information given during the call.

Before contacting Triton, please verify your requirements using 

the information contained in the supplied user guide. Triton 

cannot accept liability for incorrect part identification.

1.

 Breakdown due to: 

a)

 use other than domestic use by 

you or your resident family; 

b)

 wilful act or neglect; 

c)

 any malfunction resulting from the incorrect use or 

quality of electricity, gas or water or incorrect setting of 
controls; 

d)

 failure to install in accordance with this 

installation guide

2.

 Claims for missing parts once the product has been 

installed.

3.

 Repair costs for damage caused by foreign objects or 

substances.

4.

 Total loss of the product due to non-availability of 

parts.

5.

 Compensation for loss of use of the product or 

consequential loss of any kind.

6.

 Call out charges where no fault has been found with 

the appliance.

7.

 The cost of repair or replacement of 

isolating switches

,

 

electrical cable, fuses and/or circuit breakers or any other 
accessories installed at the same time

.

  Replacement of 

the Pressure Relief Device that 

only

 activates when the 

shower outlet is blocked, is also excluded.

8.

The cost of routine maintenance, adjustments, overhaul 

modifications or loss or damage arising therefrom, 
including the cost of repairing damage, breakdown, 
malfunction caused by corrosion, 

and 

furring

.

9.

 Call out charges where the water supply cannot be 

isolated, this includes consequential losses arising from 
unserviceable supply valves.

For the latest Terms & Conditions, please see: 

www.tritonshowers.co.uk

Customer Service:  

024 7637 2222 

Trade Installer Hotline: 02476 378344

Содержание T80 Easi-fit

































Отзывы: