manualshive.com logo in svg

Triton Novel SR, Инструкция по установке и эксплуатации

Поделиться
Скачать
Triton Novel SR Скачать руководство пользователя страница 20

Power Shower

20

FAULT FINDING

IMPORTANT: Switch OFF the electricity at the mains supply and remove the correct 
circuit fuse before attempting any fault finding inside the unit.
Any maintenance or repair to the shower must be carried out by a suitably competent 
person.
In the unlikely event of a fault occurring please contact Triton Customer service. 
DO NOT remove the shower from the installation.

Symptom Cause 

Action/Cure

1.1.1

 Turn the temperature control clockwise. 

1.2.1

 Turn the temperature control clockwise. 

1.3.1 

Remove filter and clean. If problem is with 

check valve, contact Customer Service.

1.4.1

 Isolate shower and consult a competent 

plumber or contact Customer Service.

2.1.1

 Turn temperature control anti-clockwise. 

2.2.1

 Turn temperature control anti-clockwise. 

2.3.1

 Turn shower off and wait for hot water 

cylinder to reheat.

2.4.1

 

Remove filter and clean. If problem is with 

check valve, contact Customer Service.

2.5.1

 Turn shower off. Consult a competent 

plumber or contact Customer Service.

3.1.1

 Blown fuse. Check supply. Renew fuse. If it 

fails again consult a competent electrician. 

3.1.2

 Power cut. Check other appliances and if 

necessary, contact local Electricity Supply Co.

3.2.1

 Consult a competent electrician or contact 

Customer Service.

3.3.1

 Thermal protection on motor has 

operated. Allow appliance to cool and reset 
itself. If it persists, contact Customer Service.

3.4.1

  Remove cover and connect start/stop 

switch.

1

 

Water too hot.

 

 

 

 

2

 

Water too cold. 

 

 

 

 

3

 

Pump does not 

operate.

 
 

 

1.1

 

Not enough cold water 

flowing through shower.

1.2

  Increase in the ambient 

cold water temperature.

1.3

  Cold inlet filter blocked 

or check valve sticking.

1.4

  Cold water supply 

blocked or cut off.

2.1

  Not enough hot water 

flowing through shower.

2.2

  Decrease in ambient 

cold water temperature.

2.3

  No hot water in the 

storage cylinder.

2.4

  Hot inlet filter blocked 

or check valve sticking.

2.5

  Hot water supply 

blocked or otherwise cut off.

3.1

  Interrupted power 

supply. 
 

3.2

  Electrical malfunction. 

3.3

  Motor overheated. 

 

3.4

  Start/stop switch not 

connected.

Содержание Novel SR

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды