background image

Owner’s Manual

Reliable Backup Power for Traffic Signals and Security/Wireless Equipment

Congratulations! You've purchased one of the most reliable and cost-effective outdoor uninterruptible power supplies for supporting and protecting
traffic signals, airport security, access security and wireless equipment. Traffic MOVE-UPS UPS systems keep traffic moving and citizens safer
by keeping mission-critical systems up during power outages. Traffic MOVE-UPS models help ensure vital systems preparedness and security
during disasters, terror incidents and routine power disruptions, mitigating tort liability for municipalities, states and other governmental and
corporate units. Traffic MOVE-UPS UPS systems provide traffic signals and security/wireless equipment with utility-supplied AC electricity (fil-
tered through premium ISOBAR

®

power conditioning) whenever available. Whenever power blackouts, brownouts or high voltages occur,

Traffic MOVE-UPS models immediately and automatically switch over to invert battery output (DC-to-AC) to power your connected equipment.
In addition, Traffic MOVE-UPS models continuously and reliably recharge your connected battery banks. 

Rugged Reliability for All Indoor/Outdoor Applications

• Heavy-duty, weather-resistant construction*
• Moisture-resistant, conformally-coated circuit boards*
• Compact size for tight controller cabinets

Premium Protection for Critical Equipment

• Built-in ISOBAR

®

power conditioning: spike, surge, low voltage, high voltage and lightning protection

• Rapid-recharge, high-amp, 3-stage battery charger
• Rapid, automatic transfer switching (from line power to inverter power)
• Automatic overload protection
• Relay for low battery alarm, flashing red mode (traffic signals)**

Cost-Effective Features for All Budgets

• Power-saving, high-efficiency DC-to-AC inversion
• Maintenance-free operation 
• Compatible with economical off-shelf accessories: bypass switch, battery heaters, standard 12V batteries, generator receptacles, NEMA

cabinets, etc.

• 12V DC input—allows for easy tie-in of automobile or maintenance truck power via jumper cables in event of prolonged outages
• Dead Battery Startup
• Ignition Interlock & In/Out Swap Protection

Warranty/Warranty Registration

2

Service & Maintenance

2

Safety

3

Feature Identification

4

Operation

5

Configuration

6-7

Mounting

8

Battery Selection

9

Battery Connection

10

AC Input/Output Connection

11

Troubleshooting

12

Traffic MOVE-UPS

(TMU)

Uninterruptible Power Supplies 

(UPS Systems)

Input

Output

Invert:

12 VDC

120V, 60 Hz. AC

Charge:

120V, 60 Hz. AC

12  VDC

1111 W. 35th Street, Chicago, IL 60609 USA

Customer Support: (773) 869-1234

www.tripplite.com

*

TMU Systems are moisture-resistant, not waterproof. ** Available on all models except 612 models.

Copyright © 2004. Traffic MOVE-UPS

is a trademark of Tripp Lite. All rights reserved.

Contents

W

arranty 

Registration

Register online toda

y f

or a 

chance to win a FREE 

Tr

ipp Lite product!

www

.tr

ipplite

.com/w

arr

anty

Содержание TMU Series













Отзывы: