background image

3

Installation

Input Connection

 

Connect a user-supplied power cord to the 
UPS system’s IEC-320-C14 input receptacle 

A

, located at the end of the input power 

cord. The user-supplied power cord should 
have an IEC-320-C13 connector at one 
end 

B

 and a plug compatible with the 

local site’s utility outlets at the other end. 
(Your computer’s detachable power cord is 
probably compatible.)

 

Note: The plug will vary depending on the type of power 
cord supplied by the user.

 

After connecting the user-supplied power 
cord to the UPS system’s IEC-320-C14 
input receptacle, insert the plug directly 
into a grounded 230V AC outlet. The outlet 
should not share a circuit with a heavy 
electrical load such as an air conditioner or 
refrigerator.

1

2

Power On

 

Press the ON/OFF/TEST/MUTE button 

A

 

for 1 second (the UPS will beep) to turn the 
UPS system on. The green ON/OFF light 

B

 

will illuminate when the UPS system is on.

 

Note: The UPS system will not begin to charge its battery 
until it has been turned on. Connected equipment will not 
be supported adequately during a power failure until the 
internal battery has charged for 4-6 hours. It will take up 
to 8 hours for the battery to charge completely.

3

Output Connections

 

Using the included C13-to-C14 power cord  

A

 , connect a personal computer or other 

electronic equipment to one of the UPS 
system’s IEC-320-C13 output receptacles  

B

 . Connect additional equipment with 

user-supplied power cords that have a C14 
connector at one end.

 

Note: Laser printers, large household appliances or other 
equipment with very high power requirements should not 
be connected to the UPS. The UPS will become overloaded 
if the combined power requirement for all connected 
equipment exceeds the total output capacity of the UPS 
(550VA). The VA rating for each piece of equipment can 
be found by consulting the equipment’s documentation 
and/or nameplate. If amps are shown, multiply by 230V to 
determine VA (Volts x Amps = VA). 

 

C13-to-C14 power cords (Part # P004-006) are available 
from Tripp Lite. Call +1 773 869 1234 for more 
information.

4

4

3

2

1

A

B

A

B

A

B

200704074 93-2671 MINI550X OM.in3   3

200704074 93-2671 MINI550X OM.in3   3

8/2/2007   2:58:43 PM

8/2/2007   2:58:43 PM

Содержание PRO550X








Отзывы: