manualshive.com logo in svg

Triplett CableRater, Инструкция по эксплуатации

Поделиться
Скачать
Triplett CableRater Скачать руководство пользователя страница 10

10

9.1.3 ZERO CALIBRATE Knob

The ZERO CALIBRATE knob is used to ‘calibrate’ the Transmitter to the Receiver

(more on this later). It can be turned clockwise or counterclockwise to increase

or decrease the level of the test signal generated by the Transmitter.

9.1.4 OUTPUT Connector

The OUTPUT connector is a standard F connector (the kind commonly used for

cable TV installations). The test signal generated by the Transmitter comes out

of this connector or ‘jack’. This jack is usually connected to the input of the cable

TV distribution system being tested, or, if testing individual components (like a

Splitter or Amplifier), to the input of the device being tested. This sometimes

requires the use of a ‘patch cable’.

9.2 Description of Receiver

9.2.1 Meter Push On/Off  Button

The Meter Push On/Off  button is used to turn the Receiver On and Off. If the

Receiver is Off, pressing the button will turn it On. If the Receiver is On, pressing

the button will turn it Off.

When first turned On, the Receiver’s LCD display may momentarily show ran-

dom numbers or symbols, but within a few seconds, the display should indicate

the correct level.

When turned Off, the Receiver goes into a low power standby mode waiting for

the next button press. It can remain in this mode for months without depleting

the battery. If the Backlight is turned On when the Receiver is turned Off, the

Backlight is turned off also.

9.2.2 Backlight Push On/Off  Button

The Backlight Push On/Off  button is used to turn the LCD display Backlight On

and Off. The button only works if the power to the Receiver is already On. If the

Receiver is On, pressing the button will turn the Backlight On. If the Backlight is

On, pressing the button will turn it Off.

The Backlight uses a lot of power, more power than the rest of the electronics in

the Receiver, and if left on will cut the battery life significantly. For this reason, a

separate button allows the user to decide if he needs the Backlight or not.

The Backlight is not bright, and may not be seen in normal room lighting, but it

is clearly visible in the dark, allowing the user to take readings in poorly lit sur-

roundings.

Содержание CableRater




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды