manualshive.com logo in svg

Trio Avionics Pro Pilot, Руководство по эксплуатации и установке

Поделиться
Скачать
Trio Avionics Pro Pilot Скачать руководство пользователя страница 53

 

 
Trio Pro Pilot Manual 4.1 
 

53

Alternatively, if your cruise groundspeed is typically less than 150 knots, or if you do not mind the higher 
bank angles at the higher groundspeeds, you may want to select the 

MANUAL 

mode.  In the 

MANUAL

 

mode you can set the maximum turn rate to a fixed limit.  It is adjustable from 1 degree/sec to as high as 
3 degree/sec, in increments of 1/10

th 

degree/sec.   

 
To set the 

TURN RATE

 selection, perform the following steps: 

 

1. Enter 

the 

CONFIGURATION SETTINGS

 menus as detailed previously and select the 

MAX 

TURN RATE

 menu. 

2.  Press and release the 

HMODE

 button.  The arrow will 

be placed at the 

AUTO

 (

MAN

) field 

3.  Rotate, or press the encoder to change the selection 

between 

AUTO

 and 

MAN

 

4.  If a manual rate is desired, select the 

MAN

 field and then press and release the 

HMODE

 button. 

You may take this number as low as 1 degree/sec, but be advised that this will result in very slow 
turns and autopilot performance may be unacceptably 
sluggish.   If 

AUTO

 is desired, select 

AUTO

 then 

proceed to step 6 

5.  With the arrow selecting the manual rate, rotate the 

encoder to select the desired rate 

6.  Press and release the 

HMODE

 button.   

 

The 

MAN TURN RATE

 procedure is complete and the encoder can now be used to select another menu 

screen. 

Circle Last Waypoint Setting 

This selection allows you to either home to the last waypoint in a flight plan or GOTO waypoint, or to 
track outbound from the last waypoint.   
 

 

If the option is set to 

NO

, the Pro Pilot will track directly outbound from the last waypoint in a 

flight plan, or the GOTO waypoint.  The waypoint identifier will be placed in the lower left display 
line upon waypoint passage and will flash for 10 seconds to indicate passage.   

 

 

If the option is set to 

YES

, the Pro Pilot will turn the aircraft to effectively “home” to this last 

waypoint.  Both modes remain in their respective states until the 

HNAV

 mode of the Pro Pilot is 

changed, or a new waypoint is selected. 

 
To set the

 CIRCLE LAST WPT

 selection, perform the following steps: 

 

1. Enter 

the 

CONFIGURATION SETTINGS

 menus as 

detailed previously and select the 

CIRCLE LAST 

WPT?

 screen. 

2.  Press and release the 

H MODE

 button.  The arrow 

will be placed at the 

YES

 (

NO

)  field 

3.  Rotate, or press the encoder to change the selection 
4.  Press and release the 

H MODE

 button.   

 

The 

CIRCLE LAST WPT?

 procedure is complete and the encoder can now be used to select another 

menu screen. 

Vertical Navigation Servo Deadband 

The 

VNAV

 servo deadband may be tailored to optimize vertical tracking performance for the particular 

airplane.  The factory setting of 6 is normally optimal for most application.  Lowering this number will 
increase the tracking resolution of the system, while raising the number will have the opposite effect.   
 

Содержание Pro Pilot




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды