background image

www.tridonic.com

3

Subject to change without notice. Information provided without guarantee.

Data sheet 10/21-LC896-1

LED Driver

Constant voltage

1. Standards

EN 55015
EN 61000-3-2
EN 61000-3-3
EN 61347-1 
EN 61347-2-13 
EN 62384
EN 61547
EN 62386-101 (DALI-2)
EN 62386-102 (DALI-2)
EN 62386-207 (DALI-2, including part 251, 252, 253)
According to EN 50172 for use in central battery systems
According to EN 60598-2-22 suitable for emergency lighting installations

3. Installation / wiring

2. Thermal details and lifetime

3.1 Circuit diagram

2.1 Expected lifetime

The LED control gear is designed for a lifetime stated above under reference conditions and with a failure probability of less than 10 %.

The relation of tc to ta temperature depends also on the luminaire design. 
If the measured tc temperature is approx. 5 K below tc max., ta temperature should be checked and eventually critical 
components (e.g. ELCAP) measured. Detailed information on request.

LC 100W 48V SC EXC

PRI

220–240 V

L

N

0/50/60 Hz

~

~

DA/N

DALI/DSI

DA/L

+ LED

– LED

SEC

LC 100W 48V SC EXC

PRI

220–240 V

L

N

0/50/60 Hz

~

~

DA/N
DA/L

switchDIM

220–240 V

50/60 Hz

N
L

+ LED

– LED

SEC

3.2  Wiring type and cross section

Mains supply wires

The wiring can be in stranded wires with ferrules or solid from 0.2 – 1.5 mm². 
For perfect function of the push-wire terminals (WAGO 250) the strip length 
should be 8.5 – 9.5 mm.

Secondary wires (LED module)

The wiring can be in stranded wires with ferrules or solid from 0.2 – 1.5 mm² 
(24AWG – 16AWG). 
For perfect function of the push-wire terminals (WAGO 250) the strip length 
should be 8.5 – 9.5 mm.

8.5 – 9.5 mm

wire preparation:
0.2 – 1.5 mm² 

8.5 – 9.5 mm

wire preparation:
0.2 – 1.5 mm² 

Expected lifetime

Type

Output load

ta

40 °C

50 °C

55 °C

60 °C

65 °C

LC 100W 48V one4all NF SC EXC

< 30 W

tc

42 °C

51 °C

57 °C

70 °C

74 °C

Lifetime

>100,000 h

>100,000 h

>100,000 h

85,000 h

60,000 h

> 30 – 80 W

tc

44 °C

53 °C

60 °C

74 °C

Lifetime

>100,000 h

>100,000 h

85,000 h

65,000 h

> 80 – 90 W

tc

45 °C

66 °C

69 °C

Lifetime

>100,000 h

80,000 h

70,000 h

> 90 – 100 W

tc

60 °C

69 °C

Lifetime

85,000 h

50,000 h

Содержание 28003535











Отзывы: