Trident PD765-6R0-00 Скачать руководство пользователя страница 69

Страница: 69 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

Troubleshooting Tips

Symptom Check/Action

No display at all

Check power at power connector

Not able to change setup or pro-
gramming,

LoCd

is displayed

Meter is locked, enter correct four-digit
password to unlock

Meter displays error message dur-
ing calibration (

err

)

Check:
1. Signal

connections

Input selected in

Setup

Minimum input span requirements

Meter displays

•

open

•

9999

•

-1999

•

Displays negative number,
not responding to RTD.

Check:
1.

Input selected in

Setup

2. TC/RTD

Switch

position

Corresponding signal at Signal
connector

Display alternates between

and a number

Press

Menu

to exit Max/Min

display readings.

Display response is too slow

Check filter and bypass values

Inaccurate temperature reading

Check:
1.

Temperature units (

F or

TC type or RTD curve selected

3. Offset

adjustment

4. TC

wire

used

5. Calibration

If the display locks up or the meter
does not respond at all

Cycle the power to restart the
microprocessor.

Relay operation is reversed

Check:
1. Fail-safe

Setup

Wiring of relay contacts

Relay and status LED do not
respond to signal

Check:
1.

Relay action in

Setup

Set and reset points

Meter not communicating with Me-
terView

or other programs

Check:
1.

Serial adapter and cable

Serial protocol selected

Meter address and baud rate

MeterView address and baud rate

Other symptoms not described
above

Call Technical Support for
assistance.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание PD765-6R0-00








































































Результаты поиска

Содержание PD765-6R0-00

Отзывы:

Бренды по названию

Популярные бренды

Trident PD765-6R0-00, Инструкция по эксплуатации

Результаты поиска

Содержание PD765-6R0-00

Отзывы:

Бренды по названию

Популярные бренды