Trident PD765-6R0-00 Скачать руководство пользователя страница 62

Страница: 62 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

OPERATION

For process inputs, the meter is capable of accepting positive and nega-
tive signals and displaying these signals in engineering units from -1999
to 9999 (

e.g.

a signal from -10 to +10 VDC could be displayed as -10.00

to 10.00).
The temperature inputs are displayed according to the input type and
temperature units (

F or

C) selected. RTD and Type T thermocouple in-

puts can be displayed with either 1

or 0.1

resolution.

Front Panel Buttons Operation

Button
Symbol

Description

Press to enter or exit Programming Mode,
view settings, or exit Max/Min readings
Hold to enter

Advanced

features menu.

Press to reset Max/Min readings

Press to display Max/Min readings
alternately

Press to display Max/Min reading
indefinitely while displaying Max/Min
Press ACK to acknowledge relays

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание PD765-6R0-00








































































Результаты поиска

Содержание PD765-6R0-00

Отзывы:

Бренды по названию

Популярные бренды

Trident PD765-6R0-00, Инструкция по эксплуатации

Результаты поиска

Содержание PD765-6R0-00

Отзывы:

Бренды по названию

Популярные бренды