TRIATEK FMS-1650 Скачать руководство пользователя

Страница: 71 / 82

BACnet OBJECTS

FMS-1650

The following table itemizes the list of points available for integration in a building management system (BMS). This table contains the objects for

open BACnet integration.

TRIATEK reserves the right to change product specifications without notice.

Object Instance

Functional Description

Read or Write

Analog Inputs

AI - 1

Analog Input 1 (default: Isolation Room Differential Pressure)

Read-Only

AI - 2

Analog Input 2 (default: Anteroom Differential Pressure)

Read-Only

AI - 3

Analog Input 3 (default: Isolation Room Humidity)

Read-Only

AI - 4

Analog Input 4 (default: Supply/Exhaust Duct Air Flow)

Read-Only

AI - 5

Thermistor Input 1 (default: Isolation Room Temperature)

Read-Only

AI - 6

Thermistor Input 2 (default: Duct Temperature)

Read-Only

Analog Outputs

AO - 1

Analog Output 1 (default: Isolation Room Damper Control)

Read-Only

AO - 2

Analog Output 2 (default: Anteroom Damper Control)

Read-Only

AO - 3

Analog Output 3 (spare control output)

Read-Only

AO - 4

Analog Output 4 (spare control output)

Read-Only

Binary Inputs

BI - 1

Digital Input 1 (default: Isolation Room Door Switch)

Read-Only

BI - 2

Digital Input 2 (default: Anteroom Door Switch)

Read-Only

BI - 3

Digital Input 3 (spare digital input)

Read-Only

BI - 4

Digital Input 4 (spare digital input)

Read-Only

Binary Outputs

BO - 1

Relay Output 1 (default: Primary Alarm Relay Output)

Read-Only

BO - 2

Relay Output 2 (default: Secondary Alarm Relay Output)

Read-Only

BO - 3

Relay Output 3 (spare relay output)

Read-Only

BO - 4

Relay Output 4 (spare relay output)

Read-Only

Analog Values

AV - 1

AI-1 Setpoint (Isolation Room Differential Pressure)

Read/Write

AV - 2

AI-2 Setpoint (Anteroom Differential Pressure)

Read/Write

AV - 3

AI-3 Setpoint (Isolation Room Humidity)

Read/Write

AV - 4

AI-4 Setpoint (Supply/Exhaust Duct Air Flow)

Read/Write

AV - 5

TI-1 Setpoint (Isolation Room Temperature)

Read/Write

AV - 6

TI-2 Setpoint

Read/Write

AV - 7

Air Change Rate based on Flow Input at AI-1

Read/Write

AV - 8

Air Change Rate based on Flow Input at AI-2

Read/Write

AV - 9

Air Change Rate based on Flow Input at AI-3

Read/Write

AV - 10

Air Change Rate based on Flow Input at AI-4

Read/Write

AV - 11

Alarm Relay 1 High Setpoint

Read/Write

AV - 12

Alarm Relay 1 Low Setpoint

Read/Write

AV - 13

Alarm Relay 2 High Setpoint

Read/Write

AV - 14

Alarm Relay 2 Low Setpoint

Read/Write

AV - 15

Alarm Relay 3 High Setpoint

Read/Write

AV - 16

Alarm Relay 3 Low Setpoint

Read/Write

AV - 17

Alarm Relay 4 High Setpoint

Read/Write

AV - 18

Alarm Relay 4 Low Setpoint

Read/Write

AV - 19

AI-1 Low Alarm Setpoint (low differential pressure alarm)

Read/Write

BACnet

Objects

Содержание FMS-1650



















































































Результаты поиска

Содержание FMS-1650

Отзывы:

Похожие инструкции для FMS-1650

Бренды по названию

Популярные бренды

TRIATEK FMS-1650, Руководство программиста

Результаты поиска

Содержание FMS-1650

Отзывы:

Похожие инструкции для FMS-1650

Бренды по названию

Популярные бренды