TRI tool 304 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 36

background image

TRI TOOL INC.

92-0749 Rev. 210701

14

Make the Cut

1. Connect the proper power supply.
2. Use the variable speed control knob on the top of the motor (on electric motor drives) to

adjust the cutting speed.

3. Rotate the feed Handle clockwise to bring the Cutting Head and tube closer together.

The machining operation begins when the tool bit contacts the tube or pipe.

4. If the tube end is not square to the tube axis, the tool bit will contact only a small

segment of the tube during each revolution.

5. To avoid tool bit damage, use a slow feed rate until the tool bit is contacting the pipe

continually during at least one revolution. Refer to section 6, Cutting Speeds and Feeds.

6. Continue rotating the Feed Handle clockwise until the end of the pipe is completely

machined. Do not let the tool bit(s) cut into the Saddles or the Saddle Adapter.

7. Discontinue the feed and allow the Cutting Head to rotate one to three revolutions to

improve the finish of the prep surface.

  8.  Rotate the Feed handle counter-clockwise to separate the Cutting Head from the tube.
  9.  Stop the tool rotation by releasing the Motor Trigger Switch.
10.  Rotate the Feed Handle counter-clockwise until the Cutting Head clears the tube or

pipe by at least 1/8” (3 mm) or more.

11. Loosen the upper Saddle by rotating the Saddle Handle Assembly. This will release the

tube.

«
...
14
15
16
17
18
...
»

Содержание 304





































Отзывы:

Нет отзывов

Похожие инструкции для 304

Бренд: National Instruments Страницы: 16

Бренд: Jasco Страницы: 11

Бренд: ParaBody Страницы: 6

Бренд: Sailmon Страницы: 10

Бренд: B&W Tek Страницы: 12

Бренд: b&o Страницы: 46

Бренд: Handler Страницы: 25

Бренд: Wahl Страницы: 47

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: xsto Страницы: 76

Бренд: F&V Страницы: 5

Бренд: F Care Systems Страницы: 2

Synthesis SDEC-3000

Бренд: JBL Страницы: 24

Бренд: Xilica Audio Design Страницы: 30

Бренд: LANGER EMV-Technik Страницы: 25

Electric Clamshell CSE12-208VCD

Бренд: Lang Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды