manualshive.com logo in svg

TRI tool 304, Руководство по эксплуатации

Поделиться
Скачать
TRI tool 304 Скачать руководство пользователя страница 13

Model 304 Tube Squaring Machine

92-0749 Rev. 210701

11

5.  OPERATION

WARNING

WARNING: 

DO NOT OVERIDE THE DEADMAN SWITCH. Locking down, 

obstructing, or in any way defeating the deadman switch on this unit 

may result in serious injury.

General Comments

A FRL (Filter/Regulator/Lubricator) is required to protect the warranty on all TRI TOOL INC. 

air or hydraulic driven tools. The motor warranty is void if damage occurs from contaminated 

air or lack of lubrication.
The FRL unit must be maintained as required. The frequency depends on the air supply. 

Keep the water trap drained, the filter cleaned, and the lubricator oil reservoir filled so there 

is a drop of oil every two to five seconds.

If the unit is to be left idle for 24 hours or more after being run on ‘wet’ air, squirt oil directly 

into the air motor inlet and run the motor for two to three seconds. This will prevent rusting 

and the rotor vanes from freezing.

For Hydraulic Motors, refer to the Operator’s Manual’ for specifics.

When the unit is operated in the vertical position, cutting head up, turn it upside down and 

remove the chips and/or other debris after each cutting operation. Tool life may be severely 

shortened, unless chips and/or other debris are removed.

Placement of Tool bIts

1.  Loosen the cap screw in the clamp bracket and rotate the motor handle to the desired 

position.

2.  Tighten the cap screw before turning the motor on.

3.  Select the tool bit(s) required to machine the end configuration desired, refer to section  

7, Tool Bits. When performing a tube squaring operation, install the  tool bit in any of the 

three Cutting Head slots.

•  When performing any separate machining operation such as facing, beveling, or 

counterboring, install the tool bit in any one of the three Cutting Head slots.

•  When performing any multiple machining operation such as facing, beveling or 

counter-boring, install the tool bit with one in each slot.

The use of dull tool bits or tool bits not manufactured by TRI TOOL Inc. may result in poor 

performance and may constitute abuse of this machine and therefore voids the TRI TOOL 

Inc. factory warranty.

Содержание 304





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды