manualshive.com logo in svg

TRI tool 301SP, Руководство пользователя

Поделиться
Скачать
TRI tool 301SP Скачать руководство пользователя страница 9

9

Model 301SP Tube Squaring Machine

92-0579 : Rev. 080905

NOTE:

NOTE:

MAINTENANCE

All components should be cleaned and coated with a light film of oil prior to use.
Use a clean, non-detergent oil, preferably SAE 10 (90SSU) or lighter.

The air supply for the 301SP with an Air Motor should include an adequate filter,
regulator and lubricator (FRL).

The Air Motor warranty is void if damage occurs from contaminated air or
lack of lubrication.

If the Model 301SP is operated in the vertical position (Cutting Head up), it should
be turned upside down and the chips and/or other debris removed after each cut
has been completed.

Tool life may be severely shortened, unless chips and/or other debris that
have been deposited on the Cutting Head during the machining operation are
removed.

Disassembly of the Model 301SP will void the warranty, except when performed by
a TRI TOOL Inc. designated repair technician.

Clean Up

Содержание 301SP




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды