manualshive.com logo in svg

TRI tool 301SP, Руководство пользователя

Поделиться
Скачать
TRI tool 301SP Скачать руководство пользователя страница 12

12

TRI TOOL INC.

92-0579 : Rev. 080905

CAUTION:

NOTE:

Tool Bit Tightening

Tighten the set screws to secure the tool bit to the Cutting Head.

Select the proper size Saddle for the outside diameter of the tube or pipe to be
squared.

The size of the Saddle is determined by the outside diameter of the tube or
pipe to be squared.

Do not drop the Saddle. Always place a hand under the Saddle when
installing or removing it from the Model 301SP.

INSTALLING A SADDLE IN THE MODEL 301SP

Select a Saddle for the desired diameter of the tubing to be worked. Place the
Saddle half with the (2) two clearance holes in it in the front of the Housing. Thread
in the (2) Cap Screws that hold the Saddle half into the front of the Housing. Thread
the third Cap Screw into the side of the Housing and into the Saddle half. Tighten all
(3) three Cap Screws which retain the Saddle half in the front of the Housing.

Place the other Saddle half in the Housing. Run the Clamp Knob Assy in until it
lightly presses the second Saddle half against the first Saddle half. Thread the
Shoulder Screw in through the Clamp Knob Assy into the upper half Saddle. Retract
the second Saddle half by turning the clamp Knob Assy. Install the (2) two Button
Head Screws with the (2) two Flat Washers into the front of the Housing.

Insert the tubing to be worked on into the front of the Model 301SP. Move the tube or
pipe approximately 1/16” (1.6 mm) from the tool bit.

Содержание 301SP




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды