tri-art audio S Series Скачать руководство пользователя страница 8

Страница: 8 / 20

turntable specs

Table Details:

Plinth:

3 Ply Bamboo laminate 19.05mm (3/4″)

Motor:

Single 24 Pole Synchronous AC Motor

Pulley:

Brass Pulley

Speed:

33.3 & 45 rpm

Drive:

Belt Drive

Platter:

3-ply Bamboo Laminate 19.05mm (3/4″)

Sub Platter:

Aluminum Sub Platter with Steel Shaft

Legs:

Leveling Legs

Bearing:

Bronze Collar Bearing with ABEC7 Carbonized Ceramic Ball Bearing

Dimensions:

H 15.5cm x W 40.9cm x L 33.3cm / 8 1/4″ x 16″ x 32.39″

Arm Details:

Material:

Three Ply Bamboo Laminate 12mm

Settings:

VTA & Azimuth Adjustments

Anti-Skate Adjust:

Passive Anti-Skate

Bearing Assembly:

Bronze with Brass Collar Spike and Synthetic,

High Viscosity Grease Bearing

Arm Base:

Bamboo Supports on Plinth

Wiring:

Cardas Wire 33 AWG Uninterrupted from Headshell Clips to Brass

Female RCA with Silver Plated Cartridge Clips

Level:

Micro Bubble Level Included

Arm Length:

9” / 222 mm

Tone Arm Mass:

10g

Crafted with bamboo and natural sheep’s wool.

Learn more at

triartaudio.com

Содержание S Series





















Результаты поиска

Содержание S Series

Отзывы:

Бренды по названию

Популярные бренды

tri-art audio S Series, Руководство пользователя

Результаты поиска

Содержание S Series

Отзывы:

Бренды по названию

Популярные бренды