background image

COMMANDER

UNIVERSAL IRRIGATION REMOTE CONTROL

      

FCC REGULATIONS

The user of this remote control device does 

not

 need an FCC license.

The Receiver has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. The Trans-
mitter has been tested and found to comply with Part 95 Subpart E.  These
limits are designed to provide reasonable protection against harmful inter-
ference when the equipment is operated in a commercial environment.

Canadian Certification #32151021261

2

          800-275-8558  www.remotecontroltech.com

Fault Indication                       Correction

Check if the Receiver number was inadvertently
changed.  Reprogram the Transmitter codes to match
the Receiver codes. (Press "1", "REC #")

Check the Group Code and Receiver Code dipswitches
on the Receiver.  Reprogram the Transmitter to match
the Receiver codes. (See page 13).

Use an ohmmeter to check that your connector's
wire assignment matches your controller's valve
assignment.

Install the RC Series Controller Isolation Relay
(Part #02002).

Check solenoid. Current drain is more than 3 amps
and is tripping the resetting fuse.

Ensure that the antennas are firmly attached to the
Receiver and  Transmitter.

Ensure that the antenna is clear from obstructions. The
three feet immediately surrounding the antenna are the
most crucial and should be kept clear of obstructions,
power lines, or electrical conduits, electric motors etc.

Keep the antenna as high as possible on the controller
and avoid situations where the antenna can be
shadowed by buildings or large metal structures.

Ensure that the Receiver's antenna is as far away from
electric motors, V.F.D.'s and overhead powerlines as
this type of equipment causes interference.

Receiver fails

 to

respond, but the
power light is on.

Receiver’s “Valve
On” indicator lights
during initial test,
but 

no valve or wrong

valve comes on.

Rain Bird’s RC series

controller advances
to the first station with
remote operation.

Receiver turns off 

when

one station is activated.

Short Range

27

      800-275-8558  www.remotecontroltech.com

Содержание Commander





























Отзывы: