background image

SLASH VXL • 13

TRAXXAS TQ

i

 RADIO & VELINEON POWER SYSTEM

4

Battery Compartment Specs:
• 166mm (6.54

"

) long  

x  49.5mm (1.95

"

) wide

• Height with stock strap:  

23mm (.91

"

) or 25mm (.94

"

)

• Height with Part #5827X 

options battery standoffs:   
Up to 44mm (1.73

"

)

Note: There is some flex with 
the battery strap.  It is possible 
to fit slightly taller batteries in 
the compartment.

INSTALLING THE BATTERY PACK

Install the battery pack with 
the battery wires facing the 
rear of the model. Insert the 
tabs of the battery hold-
down into the slots in the 
rear hold-down retainer and 
then place the battery hold-
down over the post. Secure 
the battery hold-down with 
a body clip in the hole in the 
post.  Do not connect the 
battery pack yet.

Using a Different Battery Configuration

The battery hold-downs are capable of accommodating either side-by-
side racing style packs or the more common stick packs. The battery 
compartments are configured for stick packs from the factory. The 
number on each side of the hold-down indicates the battery height in 
millimeters that hold-down can accommodate. Note that one side is 
labeled “25” and the other side is labeled “23”. The 25mm side is for use 
with typical stick type battery packs. If you are using side-by-side racing 
packs, simply flip the hold-down over to the 23mm side and use it on 
the opposite side of the chassis. Your model includes a foam block that 
should be installed in front of 6-cell batteries for a more secure fit. 

High-Current Connector

Your model is equipped with the Traxxas 
High-Current Connector. Standard 
connectors restrict current flow and are 
not capable of delivering the power 
needed to maximize the output of the 
VXL-3s. The Traxxas connector’s gold-plated terminals, with large 
contact surfaces, ensure positive current flow with the least amount of 
resistance. Secure, long-lasting, and easy to grip, the Traxxas connector 
is engineered to extract all the power your battery has to give.

25mm side: Standard 

NiMH stick pack setup

23mm side: Side-by-side 

NiMH pack setup

Battery iD

Your model’s included battery 
pack is equipped with Traxxas 
Battery iD. This exclusive 
feature allows Traxxas battery 
chargers (sold separately) 
to automatically recognize 
connected battery packs 
and optimize the charge 
settings for the battery. 
This eliminates the need to 
worry over charger settings 
and menus for the easiest 
and safest charging solution 
possible. Visit Traxxas.com to 
learn more about this feature 
and available Traxxas iD 
chargers and batteries.

Содержание SLASH VXL 58076-21



































Отзывы: