Traxxas 53097-3 Скачать руководство пользователя страница 52

Страница: 52 / 59

Page 4

Revo: TRX 3.3, TQi 2.4GHz Radio System, Traxxas Link Wireless Module, & TSM (Model 53097-3) Parts List

REV. 180118 1408

2075

Servo, digital high-torque (ball bearing), waterproof

2055 Servo,

high-torque

2056

Servo, high-torque, waterproof (blue case)

2060 Servo,

sub-micro

2065 Servo,

sub-micro,

waterproof

6507R

TQi 2.4 GHz High Output radio system, 4-channel with Traxxas
Link Wireless Module, TSM (4-ch transmitter, 5-ch micro
receiver)

6529

Transmitter, TQi Traxxas Link enabled, 2.4GHz high output,
3-channel (transmitter only)

6530

Transmitter, TQi Traxxas Link enabled, 2.4GHz high output,
4-channel (transmitter only)

6511

Traxxas Link Wireless Module

3035

Wiring harness for RX Power Pack, Revo (includes on/off switch and
charge jack)

Ready-To-Race Model

53097-3

Revo 3.3: 1/10 Scale 4WD Nitro-Powered Monster Truck (with
Telemetry Sensors) with TQi 2.4GHz Radio System, Traxxas Link
Wireless Module, and Traxxas Stability Management (TSM)

Rear Suspension

5334R

Axle carriers, left & right (1 each) (use with larger 6x13mm ball
bearings)/ bearing adapters (for 6x12mm ball bearings) (2)/ dust boot
retainers (4)

5323

Bulkhead tie bars, front & rear (blue-anodized aluminum)

5323R

Bulkhead tie bars, front & rear (red-anodized aluminum)

5329

Bulkhead, rear (L&R halves)/ diff retainer, rear/ 4x14mm BCS (2)

5134

Caster spacers (4)/ shims (4)

5339

Insert, threaded steel (replacement inserts for Tubes) (includes (1)
left and (1) right threaded insert)

5497

Linkage, rear sway bar (Revo/Slayer) (3x50mm turnbuckle) (2)
(assembled with rod ends, hollow balls and ball stud)

5378X

Pivot ball caps (4)/ dust boots, rubber (4)/ dust plugs, rubber (4)/ dust
boot retainers, black (4), blue (4) (2 pkgs. req. to complete truck)

4933

Pivot balls (4)/ pivot ball cap bushings (4)

4933X

Pivot balls, hard-anodized 7075-T6 aluminum (4)/ pivot ball cap
bushings (4)

5319X

Push rod (aluminum) (assembled with rod ends) (2) (red) (use
with #5359 progressive 3 rockers)

5318X

Push rod (aluminum) (assembled with rod ends) (2) (use with
long travel or #5357 progressive-1 rockers)

5319

Push rod (steel) (assembled with rod ends) (2) (black) (use with
#5359 progressive 3 rockers)

5318

Push rod (steel) (assembled with rod ends) (2) (use with long travel or
#5357 progressive-1 rockers)

5354X

Rocker arm post (aluminum) (4)

5354

Rocker arm post (steel) (2)

5356

Rocker arm set, long travel (120-T) (use with #5318 or #5318X
pushrod)

5357

Rocker arm set, progressive-1 (90-T) (use with #5318 or #5318X
pushrod)

5358

Rocker arm set, progressive-2 (90-T)/ spacers (red aluminum) (8)

5359

Rocker arm set, progressive-3 (90-T) (requires pushrods part
#5319 or 5319X)

5348

Rod ends, Revo (large, for rear toe link only) (4)

5189

Screw pins, 4x13mm (with threadlock) (4)

5133

Spacer, pushrod (aluminum, red) (use with 5318 or 5318X pushrod
and 5358 progressive 2 rockers) (8)

5333R

Suspension arm set, adjustable wheelbase (lengthens
wheelbase 10mm or 19mm) (suspension arm upper (2)/
suspension arm lower (2)/ bumper mount spacers (2)/ 4x16BCS
(2))

5333

Suspension arm upper (1)/ suspension arm lower (1) (rear, left or
right)

5328

Suspension arms, adjustable wheelbase left side (upper arm (1)/
lower arm (1))

5327

Suspension arms, adjustable wheelbase right side (upper arm
(1)/ lower arm (1))

5321

Suspension pin set (front or rear, hardened steel), 3x20mm (4),
3x40mm (2))

5498

Sway bar kit, Revo (front and rear) (includes thick and thin sway
bars and adjustable linkage) (requires part #5411 to install rear
bumper)

5496

Sway bar mounts (front & rear) (Revo)/ sway bar wires (front &
rear) (4)/ drill guide/ spacers

5338A

Toe links, Revo (Tubes 7075-T6 aluminum, black) (128mm, fits
front or rear) (2)/ rod ends, rear (4)/ rod ends, front (4)/ wrench (1)

5338R

Toe links, Revo (Tubes red-anodized, 7075-T6 aluminum,
stronger than titanium) (128mm, fits front or rear) (2)/ rod ends,
rear (4)/ rod ends, front (4)/ aluminum wrench (1)

Recoil Starter

5277

Shaft, starter (TRX 2.5, 2.5R, 3.3)

5170 Starter,

recoil (complete with screws) (TRX 2.5, 2.5R, 3.3)

Shocks (GTR)

5466R

Bodies, GTR shock (hard-anodized, PTFE-coated aluminum) (4), with
TiN shafts (4) (bodies and shafts only)

5466

Body, GTR shock (aluminum) (1)

5467A

Body, GTR shock (aluminum, blue-anodized) (1)

5467R

Body, GTR shock (aluminum, red-anodized) (1)

5466X

Body, GTR shock (hard-anodized, PTFE-coated aluminum) (1)

5465

Caps and spring retainers, GTR shock (upper cap (2)/ hollow balls
(2)/ bottom cap (2)/ upper retainer (2)/ lower retainer (2))

5475 Multi-tool

(plastic)

5158

Nuts, 2.5mm nylon locking (12)

5462

Rebuild kit, GTR shock (x-rings, bump stops, bladders, all pistons,
piston nuts, shock rod ends) renews 2 shocks

5469

Rod ends (GTR shocks) (6)

5463

Shaft, GTR shock (2) (stainless)

5463T

Shaft, GTR shock, TiN-coated (2)

5460

Shocks, GTR aluminum (assembled) (2) (without springs)

5460A

Shocks, GTR aluminum, blue-anodized (fully assembled w/o
springs) (4)

5460R

Shocks, GTR aluminum, red-anodized (fully assembled w/o
springs) (4)

5460X

Shocks, GTR hard-anodized, PTFE-coated aluminum bodies with TiN
shafts (fully assembled w/o springs) (4)

1666

Silicone shock oil (30 wt)

5461

Variable damping kit, GTR shocks (includes #1, #2, #3 pistons
and stainless steel valves)

Slipper Clutch Components

5478

Flat wrench, 8mm (blue-anodized aluminum)

5366

Input shaft, transmission (slipper shaft)

5352R

Rebuild kit (heavy duty), slipper clutch (steel disc/ aluminum
friction pads (3)/ spring, Revo (1)/ spring, Maxx (1)/ 2x9.8mm pin/
5x8mm MW/ 5.0mm NL (1)/ 4.0mm NL (1))

5352X

Rebuild kit, slipper clutch (steel disc/ friction pads (3)/ spring (2)/
2x9.8mm pin/ 5x8mm MW/ 5.0mm NL (1)/ 4.0mm NL (1))

2554

Screws, 3x6mm cap-head machine (hex drive) (6)

5351

Slipper pressure plate and hub (alloy)

Springs

5435

Spring, shock (red) (GTR) (2.6 rate yellow) (1 pair)

5436

Spring, shock (red) (GTR) (2.9 rate white) (1 pair)

5437

Spring, shock (red) (GTR) (3.2 rate orange) (std. front 90mm) (1 pair)

5438

Spring, shock (red) (GTR) (3.5 rate green) (1 pair)

5439

Spring, shock (red) (GTR) (3.8 rate gold) (1 pair)

5440

Spring, shock (red) (GTR) (4.1 rate tan) (1 pair)

5441

Spring, shock (red) (GTR) (4.4 rate black) (1 pair)

5442

Spring, shock (red) (GTR) (4.9 rate silver) (std. front 120mm) (1 pair)

5444

Spring, shock (red) (GTR) (5.9 rate blue) (std. rear 120mm) (1 pair)

5445

Spring, shock (red) (GTR) (6.4 rate purple) (1 pair)

5443

Spring, shock red (GTR) (5.4 rate pink) (1 pair)

Spur Gears & Clutch Bells

5214

Clutch bell (14-tooth)/5x8x0.5mm fiber washer (2)/ 5mm e-clip
(requires 5x10x4mm ball bearings part #4609) (1.0 metric pitch)

5215

Clutch bell (15-tooth)/5x8x0.5mm fiber washer (2)/ 5mm e-clip
(requires 5x11x4mm ball bearings part #4611) (1.0 metric pitch)

5216

Clutch bell (16-tooth)/5x8x0.5mm fiber washer (2)/ 5mm e-clip
(requires 5x11x4mm ball bearings part #4611) (1.0 metric pitch)

5217

Clutch bell (17-tooth)/5x8x0.5mm fiber washer (2)/ 5mm e-clip
(requires 5x11x4mm ball bearings part #4611) (1.0 metric pitch)

2554

Screws, 3x6mm cap-head machine (hex drive) (6)

3953

Spur gear, 36-tooth (1.0 metric pitch)

3954

Spur gear, 38-tooth (1.0 metric pitch)

3955

Spur gear, 40-tooth (1.0 metric pitch)

Steering Components

5355X

Hollow ball set, aluminum (30)/ tall centered hollow ball (2)/ tall
offset hollow ball (2)/ bump steer adjustment shims; 3.5mm (2),
1.17mm (2)

5355

Hollow ball, tall centered (2)/ tall offset hollow ball (2)/ bump steer
adjustment shims; 3.5mm (2), 1.17mm (2)

5341

Linkage, steering (Revo 3.3) (3x50mm Turnbuckle) (2)/ rod ends
(short) (4)/ hollow balls (4)

5343X

Mount, steering arm/ steering stops (2) (lower hinge pin retainer)
(includes standard and maximum throw steering stops)

5469

Rod ends (GTR shocks) (6)

5347

Rod ends, Revo (large) with hollow balls (12)

5349

Rod ends, small, with hollow balls (6) (for Revo steering linkage)

Содержание 53097-3




























































Результаты поиска

Содержание 53097-3

Отзывы:

Похожие инструкции для 53097-3

Бренды по названию

Популярные бренды

Traxxas 53097-3, Руководство пользователя

Результаты поиска

Содержание 53097-3

Отзывы:

Похожие инструкции для 53097-3

Бренды по названию

Популярные бренды