background image

INTRODUCTION

EQUIPMENT RECOMMENDED (NOT INCLUDED)

Radio Transmitter

• 

Radio receiver

• 

Batteries for Transmitter

• 

Electronic Speed Control

• 

Steering Servo

• 

540 Type Motor or Brushless Motor System

• 

Pinion Gear (48 Pitch)

• 

7.4V 2S Li-Po Pack

• 

Mini Body Shell

• 

Mini Wheels, Tires and Inserts

• 

TOOLS RECOMMENDED (NOT INCLUDED)

1.5mm, 2.0mm, 3.0mm Allen Wrench

• 

5.5mm & 7.0mm Hex Socket Wrench

• 

Modelers Craft Knife

• 

Small Cross Head Screw Driver

• 

Turnbuckle Wrench

• 

Calipers/Ruler

• 

Camber Gauge

• 

Battery Strapping Tape

• 

Instant Glue/Thread Lock

• 

Shock Oil

• 

Thrust Grease, Diff. Grease, Joint Grease

• 

Paint (for Bodyshell)

• 

NOTE:

The Sabre 4WD Mini chassis uses the best available components.  All 

• 

replacement parts can be purchased from your local hobby or model 

shop.

This instruction manual contains a blank setup sheet for your own 

• 

setup record.

Enjoy building and driving your Sabre 4WD Mini !!

Do not use your model:

• 

Near real cars, animals, or people that are unaware that an RC car 

1. 

is being driven.

In places where children and people gather

2. 

In limited indoor spaces

3. 

In wet conditions

4. 

In the street

5. 

In areas where loud noises can disturb others such as hospitals 

6. 

and residential areas

At night or anytime your line of sight to the model may be 

7. 

obstructed or impaired in any way.

To prevent any serious personal injury and/or damage to property, please 

be responsible when operating all remote controlled models.

ELECTRICAL PRECAUTIONS

Insulate any exposed electrical wiring (using heat shrink tubing or 

• 

electrical tape) to prevent dangerous short circuits.  Take maximum 

care in wiring, connecting and insulating cables.  Make sure cables 

are always connected securely.  Check connectors for if they become 

loose.  And if so, reconnect them securely.  Never use R/C models with 

damaged wires.  A damaged wire is extremely dangerous, and can 

cause short-circuits resulting in fire.

Low battery power will result in loss of control.  Loss of control can 

• 

occur due to a weak battery in either the transmitter or the receiver  

Weak running battery may also result in an out of control car if your 

car’s receiver power is supplied by the running battery.  Stop operation 

immediately if the car starts to slow down.

When not using RC model, always disconnect and remove battery.

• 

Do not disassemble battery or cut battery cables.  If the running 

• 

battery short-circuits, approximately 300W of electrical power can be 

discharged, leading to fire or burns.  Never disassemble battery or cut 

battery cables.

Use a recommended charger for the receiver and transmitter batteries 

• 

and follow the instructions correctly.  Over-charging, incorrect 

charging, or using inferior chargers can cause the batteries to become 

dangerously hot.  Recharge battery when necessary. Continual 

recharging may damage battery and, in the worst case, could build 

up heat leading to fire.  If battery becomes extremely hot during 

recharging, please ask your local hobby shop for check and/or repair 

and/or replacement.

Regularly check the charger for potential hazards such as damage to 

• 

the cable, plug, casing or other defects.  Ensure that any damage is 

rectified before using the charger again.  Modifying the charger may 

cause short-circuit or overcharging leading to a serious accident.  

Therefore do not modify the charger.

Always unplug charger when recharging is finished.

• 

Do not recharge battery while battery is still warm. After use, battery 

• 

retains heat.  Wait until it cools down before charging.

Do not allow any metal part to short circuit the receiver batteries or 

• 

other electrical/electronic device on the model.

Immediately stop running if your RC model gets wet as may cause 

• 

short circuit.

Please dispose of batteries responsibly.  Never put batteries into fire.

• 

BEFORE YOU START

The Sabre 4WD Mini is a professional 1/10 scale four-wheel drive touring 

car and should be built only by persons aged 16 years or older with 

previous experience building and operating R/C model cars.  This is not a 

toy and is not intended for use by beginners or by children without direct 

supervision of a responsible, knowledgeable adult.  Read the instruction 

manual carefully before building.

T.O.P. Racing shall not be liable for any loss, injury or damages, whether 

direct, indirect, special, incidental, or consequential, arising from the 

use, misuse, or abuse of this product and/or any product or accessory 

required to operate this product.

GENERAL PRECAUTIONS

This product is not suitable for children under 16 years of age without 

• 

the direct supervision of a knowledgeable adult.

Assemble this kit only in places away from the reach of small children.

• 

First-time builders and users should seek advice from people who 

• 

have building experience in order to assemble the model correctly and 

to allow the model to reach its performance potential.

Exercise care when using tools and sharp instruments.

• 

Take care when building, as some parts may have sharp edges.

• 

Keep small parts out of reach of small children.  Children must not 

• 

be allowed to put any parts in their mouth, or pull vinyl bag over their 

head.

Immediately after using your model, do not touch equipment on the 

• 

model such as the motor and speed controller, because they generate 

high temperatures.  You may seriously burn yourself by touching them.

Follow the operating instructions for the radio equipment at all times.

• 

Do not put fingers or any objects inside rotating and moving parts, as 

• 

this may cause damage or serious injury as your finger, hair, clothes, 

etc. may get caught.

Be sure that your operating frequency is clear before turning on 

• 

or running your model, and never share the same frequency with 

somebody else at the same time.  Ensure that others are aware of the 

operating frequency you are using and when you are using it.

Always turn on your transmitter before turning on the receiver in the 

• 

car.  Always turn off the receiver before turning off your transmitter.

Keep the wheels of the model off the ground when checking the 

• 

operation of the radio equipment.

Disconnect the battery pack before storing your model.

• 

To prevent any serious personal injury and/or damage to property, be 

• 

responsible when operating all remote controlled models.

The model car is not intended for use on public places and roads or 

• 

areas where its operation can conflict with or disrupt pedestrian or 

vehicular traffic.

Page 1

Содержание Sabre 4WD Mini S-MB01





















Отзывы: