www.traxontechnologies.com
©2019 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U.
PATENTS, JAPAN PATENTS, OTHER PATENTS PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide
06/19 V1.1
12 of 21
www.traxontechnologies.com
©2019 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U.
PATENTS, JAPAN PATENTS, OTHER PATENTS PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide
06/19 V1.1
13 of 21
2.3.2
Mounting Allegro Dot M/L
1. Allegro Dot M/L must be mounted without any stress induced at the boundary area of
the cable and Allegro Dot.
2. Allegro Dots MUST be mounted to the installation surface via the mounting holes, either
by screw or cable tie.
FIG.13: Mounting the Allegro Dot M/L
(M3 Screws not included)
Suggested alternative method
if M3 screws are not viable
(Cable ties not included)
(M3 Screws not included)
Suggested alternative method
if M3 screws are not viable
(Cable ties not included)
3. Cable segment must not be bent below 20mm from the housing of the Allegro Dot M/L
and cable overmold (Minimum Bending Length).
4. Secure the cables between Allegro Dot M/L (every 500mm, using cable tie) and create a
small clearance beneath the cable (see below diagram). Ensure no damage is generated
on the cable.
FIG.14: Securing the cable
Observe clearance
Cable tie
Mounting surface
2.3 On-Site Installation
•
DO NOT attempt installation in wet or severe weather conditions.
•
DO NOT leave and expose any Allegro Dot M/L, Pixel Distributor or LED
Engine unconnected under wet/raining or snowing environment.
•
Ensure all the cable connectors of Allegro Dot M/L are removed from the
Pixel Distributors before installing.
•
DO NOT pull on cable of Allegro Dot M/L. IP failure induced by stressed/
damaged cables during or after installation will not be under warranty by
Traxon Technologies.
•
ALWAYS keep the cables protected from sharp objects and ensure no
damage is generated on the cable.
•
Failure to keep Allegro Dot M/L within the operating temperature range of
-30°C to +60°C (+50°C for North America), -22°F to +140°F (+122°F for
North America), and storage temperature range of –40°C to 70°C (–40°F
to 158°F) will void the product’s warranty.
2.3.1
Mounting LED Engine
1. Fix LED Engine on top of Pixel Distributor with included M4 screws.
NOTE: Keep adjacent LED Engines and Pixel Distributors a minimum 150mm (5.91”)
apart for better heat dissipation.
FIG.12: Mounting LED Engine on top of Pixel Distributor
LED Engine mounts
on top of the Pixel Distributor
M4 × 8mm × 4
(Included)
(Not included)
M5 anchor bolts
(LED Engine is ordered
separately)
Mount Pixel Distributor
with connectors facing down
≥
150mm/5.91”
clearance
≥
150mm/5.91”
clearance
≥
150mm/5.91”
clearance
≥
150mm/5.91”
clearance
≥
150mm/5.91”
clearance
≥
150mm/5.91”
clearance
2. Mount the Pixel Distributor with 4 × M5 Anchor Bolts (not included). Recommended
orientation is with connectors facing DOWN (see above diagram).
