manualshive.com logo in svg

Travis Industries DVL EF II, Руководство пользователя

Поделиться
Скачать
Travis Industries DVL EF II Скачать руководство пользователя страница 26

26

 

Finalizing the Installation 

© Travis Industries 

4040808

 

100-01201_000

 

 

FINE TUNING THE EMBER-FYRE™  BURNER 

Each installation is affected by altitude, vent configuration, and fuel quality.  Because of this, the restrictor and 
air shutter may need to be fine tuned to each installation.  Follow the hints below to fine-tune the burner for 
optimum performance and aesthetics. 

Air Shutter Hints: 

•

 

For more glow, open the air shutter, however, this will make the flames more blue. 

•

 

For yellow flames, close the air shutter, however, this may create less glow. 

The flames should burn right 
off the top of the burner ports 
(if they are too blue, adjust 
the air control).

Lifting flames indicate 
insufficient draft (restrictor 
is set too high).

Burner

Burner Ports 

(holes)

Ghosting flames indicate 
insufficient air (restrictor set too 
high, air shutter shut down, or 
other venting error).

Lifting Flames

Correct Flames

Ghosting Flames

Flickering Flames

Flickering, short flames 
indicate excessive draft 
(move air shutter to a higher 
position).

 

Warning:

   If the vent configuration is installed incorrectly the vent may cause the flames inside the heater to lift or 

“ghost” – a dangerous situation.  Inspect the flames after installation to insure proper performance.  If 
the vent configuration is correct, yet the flames are lifting or ghosting, shut off gas to the heater and 
contact the dealer for information on remedying the problem.

 

8.  Replace the glass. 

9.  Attach the face following the directions included with the face.

 

NOTE

: If using the Classic Arched, Artisan, Metropolitan or 

Victorian Lace Face you must use the face mounting 
brackets included with the heater (SKU 225-20054).  See 
page 11 for details. 

10.  Turn the flame adjust knob to its highest position - the flames 

should not contact the top of the firebox.  Check the flame on 
low position.  The flames should burn off of each burner hole.  
If the heater does not work correctly, contact your dealer for a 
remedy. 

 

New Brackets

Old Brackets

 

11.  Give this manual to the home owner and fully explain the operation of this heater. 

 

Содержание DVL EF II











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды