background image

 

Optional Equipment  (for qualified installers only) 

61 

© Travis Industries 

1/10/2022 - 1559 

616 MF GSR2 

Tumbled Stone (Optional)  

 

WARNINGS

 

 

 

Do not place stones over the burner ports

 

 

Install a base layer of either Crushed Glass or Embers & EG Glass before placing any of this 
media kit. 

 

Make sure the gas control valve is OFF and the heater is cool prior to conducting service. 

 

If using propane (LP), convert the appliance before installing the media

 

 

This appliance requires the use of a fireback kit.  Install the Fireback BEFORE installing the 
media. 

Overview 

This kit contains 30 pounds of tumbled stone used to decorate the firebox.  You may use this kit alone or 
in addition to the other log kits available for this insert.  Because this kit includes more than enough 
stones, we recommend extra stones be kept for future use. 

Packing List 

  Small Stones - 10 lbs. 

  Large Stones - 20 lbs.

 

 

Placing the Media 
 

Randomly place the media on top of the Crushed Glass or Ember media. 
 

 

DO NOT PLACE MEDIA OVER BURNER PORTS (THIS WILL CAUSE SOOTING). 

 

DO NOT STACK MEDIA IN PILES THAT MAY FALL OVER OR BLOCK AIRFLOW 

 

 

 

Содержание 616 Diamond-Fyre GSR2

































































Отзывы: