Transtech PQI 301 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 36

background image

From this screen you can press ‘1’ to display the lowest density reading, highest

density reading, average density, and each of the individual readings. (These

readings can also be transferred to a personal computer using the PQI’s Remote

Mode).
Pressing ‘2’ will complete the set of readings and display the starting screen with

the location/reading reset to ‘1A’.

3.8 Automatic Moisture And Temperature

Correction

3.8.1 Moisture correction

The third generation PQI has a built in moisture correcting formula. Care should

still be used when taking PQI density readings in areas of the mat where there is

standings surface moisture.
Excessive moisture can affect the accuracy of the PQI. DO NOT take a reading

where there is signs of excessive surface moisture, ie puddles. The Relative

Water Value is displayed as “H2O” in all measurement modes of the PQI.
The third generation PQI has a built in moisture correcting formula. Care should

still be used when taking PQI density readings in areas of the mat where there is

standings surface moisture.

Continuous Mode

[B]

Batt: 12.7V

H2O: 3.2

187.6 F

D: 156.5 Lb

(87.8%)

Example of H2O being displayed

The PQI shows H2O values up to three digits.

Hint: Always wipe the sensor disk with a clean dry cloth before taking

another reading.

3.8.2 Automatic Temperature Compensation
The third generation PQI comes equipped with an infrared temperature probe

attached to the front of the PQI. Temperature readings allow for internal offset

adjustments to be made to the readings, due to extreme temperature changes on

the asphalt mat.
Temperature readings are displayed during all of the measurement modes.

Continuous Mode

[B]

Batt: 12.7V

H2O: 3.2

187.6 F

D: 156.5 Lb

(87.8%)

Example of temperature being displayed

24

«
...
23
24
25
26
27
...
»

Содержание PQI 301





































Отзывы:

Нет отзывов

Похожие инструкции для PQI 301

Solar Charging Panel-D

Бренд: Ezviz Страницы: 3

Бренд: Avalue Technology Страницы: 100

Бренд: Velleman Страницы: 4

Бренд: Palsonic Страницы: 32

Бренд: AXIOMTEK Страницы: 31

kontron FlatView HYG

Бренд: S&T Страницы: 35

VIPA HMI PPC021 ES

Бренд: YASKAWA Страницы: 57

Бренд: dacell Страницы: 32

AQUOS LC-52D85U

Бренд: Sharp Страницы: 1

Aquos LC 57D90U

Бренд: Sharp Страницы: 2

Aquos LC-32D47UA

Бренд: Sharp Страницы: 39

AQUOS LC-46D85U

Бренд: Sharp Страницы: 47

AQUOS LC-19D45U

Бренд: Sharp Страницы: 60

Aquos LC 57D90U

Бренд: Sharp Страницы: 81

Aquos LC-60LE845U

Бренд: Sharp Страницы: 94

AQUOS LC-19D45U

Бренд: Sharp Страницы: 126

Бренд: Philips Страницы: 1

52PFL7762D - annexe 1

Бренд: Philips Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды