Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Fiber cable
Bit Error Rate:
<10-9
Singlemode fiber
(recommended)
:
9 μm
Multimode fiber
(recommended)
:
62.5/125 μm
Multimode fiber
(optional)
:
100/140, 85/140, 50/125 μm
J/FE-CF-03
1300 nm multimode
Fiber Optic Transmitter Power:
min: -19.0 dBm
max: -14.0 dBm
Fiber Optic Receiver Sensitivity:
min: -30.0 dBm
max: -14.0 dBm
Link Budget:
11.0 dB
J/FE-CF-03(SC)
1300 nm multimode
Fiber Optic Transmitter Power:
min: -19.0 dBm
max: -14.0 dBm
Fiber Optic Receiver Sensitivity:
min: -30.0 dBm
max: -14.0 dBm
Link Budget:
11.0 dB
J/FE-CF-03(SM) & (LH)
1300 nm singlemode
Fiber-optic Transmitter Power:
min: -15.0 dBm
max: -8.0 dBm
Fiber-optic Receiver Sensitivity:
min: -31.0 dBm
max: -8.0 dBm
Link Budget:
16.0 dB
J/FE-CF-03-100
1310 nm (TX)/1550 nm (RX) simplex
J/FE-CF-03-101
1550 nm (TX)/1310 nm (RX) simplex
Fiber-optic Transmitter Power:
min: -13.0 dBm
max: -6.0 dBm
Fiber-optic Receiver Sensitivity:
min: -32.0 dBm
max: -3.0 dBm
Link Budget:
19.0 dB
Copper cable
Category 5:
Gauge:
24 to 22 AWG
Attenuation:
22.0 dB/100m @ 100 MHz
Maximum Cable Distance:
100 meters
•
Straight-Through or Crossover cable may be used.
• Shielded Twisted-Pair (STP) or Unshielded Twisted-Pair (UTP) may be used.
• Pins 1&2 and 3&6 are the two active pairs in an Ethernet™ network .
• Use only dedicated wire pairs for the active pins:
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
• Do not use flat or silver satin wire.
6
J/FE-CF-03
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
7
[email protected] -- Click the “Transition Now” link for a live Web chat.
Technical Specifications
For use with Transition Networks Model J/FE-CF-03 or equivalent
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
Standards:
IEEE 802.3™
Data Rate:
100 Mb/s
Case Dimensions:
3.9" x 3.0" x 1.0"
(100mm x 76mm x 25mm)
Shipping Weight:
2 pounds
(0.9 kilograms)
Power Consumption:
2.8 watts, 200 mA @ 13.9 VDC
Power Supply DC Output:
12 VDC, 0.4 A
(minimum)
minimum output regulation: 5%
Connector: 2.1mm barrel, center pin positive
MTBF*
48,135 hours
(MIL217F2 V5.0) (MIL-HDBK-217F)
128,553 hours
(Bellcore7 V5.0)
Environment:
Tmra**:
0 to 60°C
(32 to 140°F)
Storage Temp:
-20 to 85°C
(-4 to 185°F)
Humidity:
5-95%, non-condensing
Altitude:
0-10,000 feet
Warranty:
Lifetime
**Manufacturer’s rated ambient temperature.
WARNING: Visible and invisible laser radiation when open. Do not stare into the
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other than
those specified herein may result in hazardous radiation exposure.
CAUTION: Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232,
RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be connected to intra-
building
(inside plant)
link segments that are not subject to lightening transients or
power faults. Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB,
RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are NOT to be connected to inter-
building
(outside plant)
link segments that are subject to lightening transients or power
faults. Failure to observe this caution could result in damage to equipment.
*MTBF is estimated using the predictability method. This method is based on MIL-
217F at 25°C ambient temperature, typical enclosure heat rise of 10°C, and nominal
operating conditions and parameters. Installation and configuration specific MTBF
estimates are available upon request. Contact Technical Support.
