6
CAPTF33xx-1xx
24-hour Technical Support:
1-800-260-1312
-- International:
00-1-952-941-7600
Installation
-- Continued
Install the Slide-In-Module
CAUTION:
Wear a grounding device and observe electrostatic discharge
precautions when installing the media converter.
Failure to observe this
caution could result in damage to, and subsequent failure of, the media
converter.
To install the CAPTF33xx-1xx media converter slide-in-module:
1.
Locate an empty installation slot on the
PointSystem™
chassis.
2.
Carefully slide the slide-in-module into the installation slot, aligning the
module’s circuit board with the installation guides.
3.
Ensure that the module is firmly seated inside the chassis.
4.
Push in and rotate the attached attached panel fastener screw clockwise
to secure it the module to the chassis front.
10BASE-T
INPOR
T
OUTPOR
T
DB-9
12C
12C-1
TERM
INIT
LKS
PWR
LKM
LKS
PWR
LKM
Multimode
Singlemode
TX
RX
TX
RX
LKF
PWR
RXF
RXC
LKC
SPD
PWR
FRX
CRX
FLNK
CLNK
RX
TX
100BASE-TX
RX
TX
100BASE-FX
Link Alert
E
D
0
50½
Multimode
Singlemode
TX
RX
TX
RX
LA
PWR
RXF
RXC
LNK
COL
10BASE-2
10BASE-FL
LKS
PWR
LKM
LKS
PWR
LKM
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
10BASE-T
10BASE-FL
Media
Conversion
Center
Power
In Use
1
Power
In Use
2
RX
TX
LNK
PWR
RESET
DB-9
Panel Fastener Screw
7
Click the “
Transition Now
” link for a live Web chat.
Installation
-- Continued
Install the Cable -- Standard Configuration
NOTE:
Unit B
must
be configured for Standard Configuration (see page 4).
Fiber
1.
Locate or build fiber cable with male, two-stranded TX to RX connectors
installed at both ends.
2.
Connect the fiber cables to
Unit A
(CAPTF33xx-100) as described:
•
Connect the male
TX
cable connector to the female
TX
port.
•
Connect the male
RX
cable connector to the female
RX
port.
3.
Connect the fiber cables to
Unit B
(CAPTF33xx-110) as described:
•
Connect the male
TX
cable connector to the female
RX
port.
•
Connect the male
RX
cable connector to the female
TX
port.
Copper
1.
Locate or build copper cables with male, RJ-
11C connectors installed at both ends.
2.
Connect the copper cables to
Unit A
(CAPTF33xx-100) as described:
•
Connect the RJ-11C connector at one
end of the cable to the RJ-11C port
on
Unit A
.
•
Connect the RJ-11C connector at the
other end of the cable to the RJ-11C port
on the Central Office
.
3.
Connect the copper cables to
Unit B
(CAPTF33xx-110) as described:
•
Connect the RJ-11C connector at one
end of the cable to the RJ-11C port
on
Unit B
.
•
Connect the RJ-11C connector at the
other end of the cable to the RJ-11C port
on the telephone device
.
ACT SDF PWR
TX
RX
ACT SDF PWR
TX
RX
Copper
Connect to the
RJ-11C connector
on the Central Office.
Copper
Connect to the
RJ-11C connector
on the telephone device.
Unit A
Unit B
Unit A
Unit B
