background image

Table of Contents 

Introduction ...............................................................................................1

 

Before Getting Started ..............................................................................1

 

Handheld Reader Setup Instructions ........................................................1

 

Charging the Encompass 1d Handheld Reader ...............................................2

 

Battery Status Light-Emitting Diode Indicator ......................................3

 

Using Your Encompass 1d Handheld Reader ..............................................4

 

Reading Tags ...........................................................................................6

 

Resetting Your CE5000B-series Mobile Computer .....................................9

 

Encompass 1d Handheld Reader Specifications .............................................9 

List of Figures 

Figure 1. Modular Charger Connector ..................................................... 2 
Figure 2. Battery Status LED ................................................................... 2 
Figure 3. Ethernet Office Cradle with Charger ......................................... 3 
Figure 4. Encompass 1d Reader in Office Cradle ................................... 4 
Figure 5. On/Off Key ................................................................................ 4 
Figure 6. Startup Menu ............................................................................ 5 
Figure 7. TagReaderDemo in Programs .................................................. 6 
Figure 8. Sample Display of ATA Tag Read ............................................ 7 
Figure 9. Sample Display of Half-Frame Wiegand Tag Read .................. 7 
Figure 10. Sample Display of an eGo or eGo Plus Tag Read ................. 8 
Figure 11. Sample Display of an IT2000 (Allegro) Tag Read .................. 8 
Figure 12. Sample Display of a Title 21 Tag Read .................................. 9

 

Safety/Regulatory/Compliance 

To comply with RF exposure limits, bystanders should stay away from the front of 
this product, at least 7.9 inches (20 cm), when it is operating. This product 
complies with all other RF exposure requirements while the unit is operating, 
including specific absorption rate (SAR) limits for the use

r’s hand. 

 
The TransCore RFID End Cap Reader has been tested and found to comply with 
the limits for a Class A digital device pursuant to Part 15 of the FCC rules. These 
limits are designed to provide reasonable protection against harmful interference 
when the equipment is operated in a commercial environment. This equipment 
generates, uses, and can radiate RF energy and may cause harmful interference 
to radio communications if not installed and used in accordance with the 
instruction manual. Operating this equipment in a residential area is likely to cause 
harmful interference, in which case, depending on the regulations in effect, the 
user may be required to correct the interference at their own expense. 
 

 

Содержание Encompass 1d













Отзывы: