Trango Systems M2400S Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 50

background image

Basic

Configuration via Browser Interface

Trango Broadband Wireless — User Manual M2400S Rev A

Page

15

Configure Basic SU Parameters

In order to establish a working link, the Base ID in the SU must match the Base ID of the AP.

SU Basic Setup:

1.

Connect to the SU (see Getting Started) and open the Configuration page.

2. Set Base ID (must match the AP).

3. Set IP, subnet, and gateway, or leave at default settings. Keep in mind if you change the IP Settings of the

radio you will loose your HTTP session when you save and activate.

4. Ensure default Opmode is "ON."

5. Save and Activate Settings.

6. If Opmode is “OFF,” click Opmode ON.

At this point, if all parameters have been set correctly and the radios are within range, a wireless link between the AP and
SU will automatically become established. Once this occurs the SU will be in “associated” status.

Allow approximately 60 seconds for the radios to complete the boot-up cycle and to associate. If the AP is busy
servicing many SUs, the association process may take slightly longer.

«
...
17
18
19
20
21
...
»

Содержание M2400S



















































Отзывы:

Нет отзывов

Похожие инструкции для M2400S

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 140

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 48

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 178

DI-624S - AirPlus Xtreme G Wireless 108G USB Storage...

Бренд: D-Link Страницы: 22

Бренд: CIS Страницы: 27

Бренд: TP-Link Страницы: 2

Бренд: BenQ Страницы: 15

Бренд: Youwon Страницы: 4

Бренд: OBERON Страницы: 2

Бренд: MFOURTEL Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды