Trane Tracer ZN521 Скачать руководство пользователя страница 18

Страница: 18 / 60

CNT-SVX07D-EN

Input/output functions and wiring for typical applications

Figure 6.

AI4 terminal wiring: RH measurement

Binary outputs

The ZN521 zone controller supports fan coil, blower coil, and unit ventilator applications that may
include the following components:
•

Supply fan with up to three speeds

•

Hydronic cooling and/or heating coils with two-position or tri-state modulating control valve

•

DX cooling (single stage)

•

Electric heat (single stage or two stage)

•

Baseboard heat (single stage)

•

Tri-state modulating outdoor/return air damper

•

Tri-state modulating face-and-bypass damper

The Tracer ZN521 controller includes ten binary outputs. Each binary output is a triac with a rating
of 12 VA at 24 Vac.

Table 6

describes the function of each output.

Tracer ZN521

RH sensor

Table 6.

Binary output functions

Binary output

Functions

• Fan high

• Fan medium
• Exhaust fan or damper

• Fan low

• Modulating cooling/changeover valve, open
• Two-position cooling/changeover valve
• DX cooling

• Modulating cooling/changeover valve, close
• Face-and-bypass damper, open to face

• Modulating heating valve, open
• Two-position heating valve
• Electric heat, stage 1

• Modulating heating valve, close
• Face-and-bypass damper, close (bypass)
• Electric heat, stage 2

• Outdoor air damper, open (return air damper, close)

• Outdoor air damper, close (return air damper, open)

• Baseboard heat
• Generic

Содержание Tracer ZN521





























































Результаты поиска

Содержание Tracer ZN521

Отзывы:

Похожие инструкции для Tracer ZN521

Бренды по названию

Популярные бренды

Trane Tracer ZN521, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Tracer ZN521

Отзывы:

Похожие инструкции для Tracer ZN521

Бренды по названию

Популярные бренды