Trane IntelliPak 2 Series, Инструкция по установке, эксплуатации и обслуживанию

Страница: 47 / 220

RT-SVX24Q-EN 47
Figure 21. Ductwork conversion
See Detail A
Detail A
Vertical Support
Align Gasket
To Base Rail
Surface
Gasket
1/4” Thick x 1” Wide
Gasket to Butt Up to
Vertical Support Surface
Typical Both Sides
Vertical Support/Base Rail Bottom
Gasket Application Details
Base Rail
Unit Rigging and Placement
W WA AR RN NIIN NG G
H He ea av vy y O Ob bjje ecctt!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on nss b be ello ow w cco ou ulld d rre essu ulltt iin n
u un niitt d drro op pp piin ng g w wh hiicch h cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y,, a an nd d e eq qu uiip pm me en ntt o orr p prro op pe errtty y--o on nlly y
d da am ma ag ge e..
E En nssu urre e tth ha att a allll tth he e lliiffttiin ng g e eq qu uiip pm me en ntt u usse ed d iiss
p prro op pe errlly y rra atte ed d ffo orr tth he e w we eiig gh htt o off tth he e u un niitt b be eiin ng g
lliifftte ed d.. E Ea acch h o off tth he e cca ab blle ess ((cch ha aiin nss o orr sslliin ng gss)),, h ho oo okkss,,
a an nd d ssh ha acckklle ess u usse ed d tto o lliifftt tth he e u un niitt m mu usstt b be e cca ap pa ab blle e
o off ssu up pp po orrttiin ng g tth he e e en nttiirre e w we eiig gh htt o off tth he e u un niitt.. L Liiffttiin ng g
cca ab blle ess ((cch ha aiin nss o orr sslliin ng gss)) m ma ay y n no ott b be e o off tth he e ssa am me e
lle en ng gtth h.. A Ad djju usstt a ass n ne ecce essssa arry y ffo orr e ev ve en n u un niitt lliifftt..
1. To configure the unit Center-of-Gravity, utilize
TOPSS or contact the local Trane sales office.
2. Attach adequate strength lifting slings to all lifting
lugs. The figures beginning with Figure 23, p. 48
show the minimum distance between the lifting
hook and the top of the unit and illustrate the
installation of spreader bars to protect the unit and
to facilitate a uniform lift. lists typical approximate
minimal unit operating weights. To determine
additional component weight, see .
3. Test lift the unit to ensure it is properly rigged and
balanced, make any necessary rigging adjustments.
4. Lift the unit and position it over the curb and
pedestal. These units have a continuous base rail
around the air handler section which matches the
curb.
IIm mp po orrtta an ntt:: For replacements, remove old gasket
from the roof curb and place new
gasket material on curb. See
“,” to
determine gasket material length using
roof curb dimensions.
5. Align the base rail of the unit air handler section
with the curb rail while lowering the unit onto the
curb. Make sure that the gasket on the curb is not
damaged while positioning the unit. (The pedestal
simply supports the unit condenser section)
A cross section of the juncture between the unit and
the roof curb is shown below.
Figure 22. Curb cross section
Gasket
Base Pan
Lifting
Lug
14 1/16
1 13/16
2
1/2
2”x4”
IIn nsstta alllla attiio on n